350-20071
4
EN nNiko sa I PM350-20071
Read the complete manual before carrying out the installation and activating the system. Keep the
manual for future reference.
1.
The presence or absence detector 360° (slave) for flush mounting consists of an integral unit with
on-off control of one channel and a motion sensor (PIR or passive infrared technology).
Y
4.2.).
The slave will control the lighting according to the parameters set on the master
refer to the manual supplied with the master
2.
2.1.
Danger: Disconnect all power before installing the detector
until installation has been completed.
Refer to the wiring diagram (fig. 1).
2.2.
Tip: Do not install the detector in the vicinity of heat sources such as stoves or electric heaters,
(ventilation systems) or any moving objects (fig. 2).
motion and heat in its surroundings.
Tip:
2.5 m:
of 80cm (table height) (fig. 3).
The detector is suited for flush mounting using a standard flush-mounting box (fig. 4).
mounting box with spring terminals (350-20057) can be used.
Y
3.
3.1.
Using the two DIP switches you set the sensitivity of the motion sensor .
options:
the desired sensitivity
At delivery the motion sensor of this detector is set at the high sensitivity mode.
3.2.
Contrary to the master
activating the walking test (fig. 6).
The detection area is tested by activating the integrated motion sensor for the walking test :
1.
The blue indication LED lights up when you activate the test mode.
The lighting is switched on for five seconds and the red indication LED lights up each time the sensor
detects activity
up.
2.
If you forget to close the test mode, the detector will return to the selected settings after five minutes.
4.
4.1.
The detector should not be powered until all cables are connected.
be ready for use after approximately 40 seconds (warm-up time).
The red indication LED flashes during warm-up time.
LED will flash briefly twice.
4.2.
The detection area can be increased by adding an extra detector (slave) (350-20071).
slaves can be connected to one master (350-20070).
on the master
m).
of approximately 30% (fig. 7).
If you would like to exclude motion detection in a portion of the detection area or if the detection area is too
large,
to 24 m.
5. MAINTENANCE
Dirt may prevent the detector from functioning properly
damp cloth and water with some detergent to clean the lens. Never exert pressure to wipe the lens clean.
the lens or other parts of the detector are defective,
6.
dimensions
46,4 x 100 mm (HxB)
73.4 x 100 mm (HxW) (including non-visible part)
power supply voltage 230
power consumption 0,2 W
mounting height (fig. 2 – 3,4 m
detection angle (fig. 360°
detection range (fig. circular
wire input 3 x 2,5 mm²
protection degree IP54
protection class
class I devices
ambient temperature -5 – +50°C
quality mark CE marked in compliance with EN 60669-2-1
accessories presence or absence detector 360° (master) (350-20070)
flush-mounting box with spring terminals (350-20057)
7.
- Th
- Th
it sh
suppor
- Dur
- the s
- the t
- this u
each specific inst
- the r
This product complies with all of the relevant European guidelines and regulations. If applicable,
the EC declaration of conformity regarding this product at www.niko.eu.
8.
In case of doubt or for the specific exchange procedure in case of a possible defect, contact the Niko support
service in Belgium at +32 3 778 90 80 or your wholesaler/installer
be found at www.niko.eu under the
9.GUARANTEE PROVISIONS
- Th
of th
- Th
the def
- In c
whi
- Nik
use, incorrect operation, transformation of the product, maintenance that does not
inst
- Th
pro
chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned
rules and
Do not dump this product with the unsorted waste. Bring it to a recognised waste collection point.
and importers, you have an important role to play in the advancement of sorting,
and electronic appliances. In order to finance the waste collection and processing,
contribution in some cases (included in the purchase price of this product).
