13
De
Ru
Se
Nl
It
Dk
Pl
Hu
Cz
Fi
No
Ro
Messung
V orsicht — Die V erwendung von Einstellelementen
oder Justagen oder die Ausführung von ander en als
den hierin angegebenen V er fahren k önnen zu einer
gefährlichen Strahlenbelastung führen.
1. Legen Sie eine Batterie ins Batteriefach. (Siehe
„Einsetzen und Wechseln der Batterie")
2. Dioptrin-Einstellung
Stellen Sie den Dioptrinwert ein, um ein klares Bild
auf dem L C-Display zu erhalten.
Drehen Sie den Dioptrin-Einstellring zuerst bis
zum vollständigen Anschlag links herum. Schalten
Sie danach das Gerät ein, um das L C-Display
zu aktivieren, wenn Sie durch den Nikon Laser-
Entfernungsmesser schauen. Drehen Sie den
Dioptrin-Einstellring im Uhrzeigersinn, bis das
Display scharf dargestellt wird.
Wird der Dioptrin wert nicht entsprechend Ihrem
Sehvermögen eingestellt, sind Sie nicht in der Lage ,
Ihr Ziel korrekt zu fokussieren.
3. Messen
Stellen Sie vor der Messung sicher , dass Sie die
Maßeinheiten eingestellt haben.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Sofort nach dem Einschalten.
(Initialisierung)
Standby Zielfokussierung
3. Drücken Sie die POWER- T aste/Messtaste einmal, um die einzelne
Messung zu aktivieren.
Halten Sie die T aste gedrückt, um die kontinuierliche Messung von
bis zu 20 Sekunden zu aktivieren.
Messung
4. Das interne Display zeigt während der Messung jew eils die
Meldung „Entfernung“ oder „Messung fehlgeschlagen“ an. (Das
Laserstrahlzeichen blinkt.)
Messung
fehlgeschlagen oder
nicht imstande,
Entfernung zu messen.
Zeigt die
gemessene Zahl
an (Ziel 1).
Zeigt die
gemessene Zahl an
(Ziel 2).
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
5. Nach der Messung werden die gemessenen Ergebnisse
ca. 8 Sekunden lang angezeigt und dann schaltet sich der
Entfernungsmesser ab.
Wenn Sie die
POWER- T aste/Messtaste
während des Einschaltens (während das int erne Display aktiv ist)
drücken, wird eine weitere Messung aktiv .
1. Schalten Sie das Gerät ein
(Überprüfen Sie, ob das interne
Display eingeschaltet ist).
(Abschaltautomatik nach ca. 8
Sekunden ohne Bedienung.)
2. V isieren Sie das Ziel an.
Positionieren Sie das
Ziel in die Mitte des
F adenkreuzes.