Bedienungsanleitung Nikon Archers Choice MAX (Seite 7 von 43) (Englisch, Französisch, Portugiesisch, Spanisch)

733843

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

12 13

Internal display

1. 『』- Target aiming/Laser irradiate system

『

』- Aim at the target. Position the target at the center of the reticle.

『

』- Appears while the laser is being used for a measurement.

(Remains present during single measurement. Blinks during continuous measurements.)

  Warning:Donotlookintotheobjectivelenseswhenthismarkisshown.

2．『

』- Distance/measurement status display

Digitally indicates measured distance in meters or yards. Also indicates measuring

status such as “Measurement in progress”, “Measurement unsuccessful” or “Unable to

measure.”

(Distance)

Display of results: ( ＜ 999.9m/yards) e.g. 234.9 meters = 『

』

Display of results: ( ≧ 1,000m/yards) e.g. 1,065 yards = 『

』

『

』Now measuring

『

』Failure to measure or unable to measure distance

3. 『

』Display units

『』Indicates distance being measured in meters.

『

』Indicates distance being measured in yards.

4. 『

』Indicates battery condition. (See "Changing Batteries")

5. 『

』Display modes

A. Horizontal Distance Mode

　『』Calculates horizontal distance to your target by measuring the linear distance and angle, and displays the

results.

B. Linear Distance Mode

　『 (no sign) 』 Calculates linear distance to your target and displays the results.

6. 『

』Target Priority mode

First Target Priority mode

　『

』Indicated when First Target Priority mode is set.

Distant Target Priority mode

　『

』Indicated when Distant Target Priority mode is set.

Although the LCD was produced using the most advanced

technology, it is impossible to eliminate dust completely.

Whenusingthisproduct,theLCDismagnifiedbyhigh

magnification of the eyepiece lens and dust may appear as a

defect. It will not, however, affect measurement accuracy.

Operational summary

Caution — use of controls or adjustments or

performance of procedures other than those

specified herein may result in hazardous radiation

exposure

1. Install a battery in the battery chamber. (See "Changing

Batteries")

2. Rubber eyepiece cup

Both eyeglass wearers and non-wearers can use this

rangefinder without attaching the rubber eyepiece cup.

3. Diopter adjustment

Adjust diopter to obtain a clear image in the LCD.

First, rotate the diopter adjustment ring counterclockwise

until it comes to a complete stop. Next, turn on the power

to activate the LCD when you look through the Nikon

RifleHunter 1000/Archer's Choice MAX. Rotate the diopter

adjustment ring clockwise until the display comes into focus.

If the diopter is not adjusted to correspond to your

eyesight, you may not be able to aim your subject.

7. Active Brightness Control Viewfinder

Active Brightness Control Viewfinder detects light conditions

of the ground area mainly in the view field

and, when

necessary, automatically turns on the orange LED illumination.

The brightness of the orange illumination is adjusted

automatically according to the light conditions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nikon Archers Choice MAX Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info