604479

Nikon Callaway RAZR Seite 31

31
Zoom out
Zoom in
Vorherige Seite
1/35
Nächste Seite
60 61
En
Fr
Es
Pt
En
Fr
Es
Pt
1. 『 』- Marca de alvo/irradiação do laser
『
』- Mire no alvo. Posicione o alvo no centro do retículo.
『 』- Aparece enquanto o laser está sendo usado para uma medição.
(Este telêmetro a laser não dispõe de uma única função de medição.)
Advertência: Não olhe para dentro das objetivas quando esta marca é
exibida.
2．『
』: exibição do status da distância/medição.
Indica, de forma digital, a distância medida, em metros/jardas. Também indica o
status da medição como "Measurement in progress” (Medição em andamento),
“Measurement unsuccessful” (Medição não foi bem sucedida) ou “Unable to measure" (Incapaz de medir).
<Exemplos de resultados de medição>
(Distância)
Exibição dos resultados: ( ≧ 100m/jardas) p.ex., 234 metros = 『
』
Exibição dos resultados: ( ＜ 100m/jardas) p.ex., 76,5 jardas = 『
』
『
』 - Medindo agora
『
』 - Falha na medição ou incapaz de medir a distância.
3. 『
』Exibição de Unidades:
『
』Indica a distância que está sendo medida, em metros.
『
』Indica a distância que está sendo medida, em jardas.
4. 『
』Indica a condição da pilha. (Ver "Troca da Pilha")
* Embora o LCD seja produzido com o uso da mais avançada tecnologia, é impossível eliminar completamente
a poeira. Geralmente, um LCD exibe na mesma magnificação ou inferior, porém, o LCD desta unidade é
altamente magnificado pela lente ocular. Por conseguinte, ao usar este produto, pode aparecer poeira como
defeito. Isto, no entanto, não afetará a precisão da medição.
Visor interno Resumo Operacional
Cuidado — O uso de controles e ajustes ou a
execução de procedimentos que não aqueles
especificados nestas instruções podem resultar
em exposição a radiações perigosas.
1. Instale uma pilha no compartimento da pilha.
(Ver "Troca da Pilha")
2. Ajuste da dioptria
Ajuste a dioptria para obter uma imagem nítida no
LCD.
Em primeiro lugar, gire o anel de ajuste da
dioptria no sentido anti-horário até que este pare
completamente. Em seguida, ligue a energia para
ativar o LCD quando você olha através do Telêmetro
a Laser Nikon. Gire o anel de ajuste da dioptria no
sentido horário até que o visor entre em foco.
Se a dioptria não for ajustada para corresponder
à sua visão, você pode não conseguir mirar
corretamente no seu objeto.
3. Medição
Antes de medir, certifique-se de confirmar o ajuste
da unidade.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
1. Pressione o botão POWER
para ligar a energia.
2. Mire no alvo.
Imediatamente
após ligar a energia.
(Inicialização)
Em espera. Mira do alvo.
3. Pressione o botão POWER uma vez para iniciar a medição contínua por
8 segundos. (O modo de medição simples não está disponível neste
modelo de telêmetro a laser).
Medição.
4. Por 8 segundos, o visor interno mostra alternadamente o indicador
“distance” (distância) e “fail to measure” (falha na medição). (Marca de
irradiação do laser está piscando).
Falha na medição ou
incapaz de medir a
distância.
Exibe o número
medido (Alvo 1).
Exibe o número
medido (Alvo 2).
5. Após a medição contínua, os resultados medidos são exibidos
por 8 segundos e, depois, a energia é desligada. Se você
pressionar o botão POWER quando a energia estiver ligada
(enquanto o visor interno estiver ativo), tem início uma outra
medição de 8 segundos.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
… 31 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Nikon Callaway RAZR wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info