31254
21
Zoom out
Zoom in
Vorherige Seite
1/56
Nächste Seite
- 21 -
Setup: Connecting the SCSI Cable
Connecting the SCSI Cable
Communication between your computer and the LS-2000
relies on the Small Computer System Interface, or SCSI, stan-
dard. For connection to the scanner and other SCSI devices, a
SCSI controller must be installed in your computer. While
Macintosh computers come with a SCSI controller built-in, most
IBM PC/AT compatibles require a SCSI controller to be installed
in the form of a SCSI expansion board or PCMCIA card. Nikon
recommends Adaptec SCSI adapters with the 32-bit version of
WINASPI.DLL for computers running Windows 95 or Win-
dows NT 4.0 (a list of adapters that have been tested and
approved by Nikon is provided separately).
To install a SCSI adapter in a computer running Windows 95 or
Windows NT 4.0, follow the instructions provided by the
manufacturer. In the case of expansion boards and some
PCMCIA cards, it is necessary to turn the computer off and
disconnect the power cable and all peripheral devices before
beginning installation. When the computer is powered on after
installation, the Windows Hardware Wizard should detect the
SCSI adapter and, if necessary, prompt you to install driver
software for the device. Once installation is complete, check to
be sure that the system resources used by the adapter do not
conflict with those used by other devices. If any conflicts are
found, resolve them as instructed in the manufacturer’s manual.
Caution: Do not attempt to connect the scanner to your
computer until a SCSI adapter has been installed and any resource
conflicts resolved.
After installing a SCSI adapter on a com-
puter running Windows 95, check for
resource conflicts.
1. Click the My Computer icon with the
right mouse button and select Properties
from the menu that appears. The
System Properties window will be
displayed. Open the Device Manager tab.
2. If the card has been installed correctly, the System Properties window
will contain a “SCSI controllers” icon. If “?” “!” or “” is showing
next to the name of the SCSI adapter, there is a problem which must
be resolved before the scanner can be connected. To determine the
cause of the problem, select the adapter icon and click the Proper-
ties button to view the drivers and system resources for the device.
SCSI controller
21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Nikon COOLSCAN_LS2000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Nikon COOLSCAN_LS2000

Nikon COOLSCAN_LS2000 Bedienungsanleitung - Deutsch - 45 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info