570991

Nikon Coolshot Seite 103

103
Zoom out
Zoom in
Vorherige Seite
1/139
Nächste Seite
204 205
No
En
Jp
Fr
Es
Pt
Ru
Se
Nl
De
It
Dk
Pl
Hu
Cz
Fi
Ro
No
En
Jp
Fr
Es
Pt
Ru
Se
Nl
De
It
Dk
Pl
Hu
Cz
Fi
Ro
Sammendrag av bruk
Forsiktig: Bruk av kontroller, justering eller
utførelse av prosedyrer på andre måter enn det
som beskrives her, kan føre til eksponering av
farlig stråling.
1. Sett inn et batteri i batterirommet. (Se Skifte
batteri)
2. Diopterjustering
Juster diopteret slik at du får et klart bilde på LCD-
skjermen.
Roter først diopterjusteringsringen mot urviseren til
den stopper helt opp. Slå deretter på strømmen for
å aktivere LCD-skjermen når du ser gjennom Nikon-
laseravstandsmåleren. Roter diopterjusteringen
med urviseren til displayet kommer i fokus.
Hvis diopteret ikke justeres slik at det passer med
ditt syn, vil du kanskje ikke kunne sikte skikkelig på
objektet.
3. Måle
Før du foretar en måling, må du kontrollere
innstillingen av enheten.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
1. Trykk på på/av-knappen
for å slå på strømmen.
2. Sikt på målet.
Umiddelbart etter
at strømmen er slått
på.(Initialiserer)
Standby. Målfokusering.
3. Trykk på på/av-knappen én gang for å starte kontinuerlig måling
i 8 sekunder. (Modus for enkeltmåling er ikke tilgjengelig i denne
laseravstandsmåleren.)
Måler.
4. I 8 sekunder viser det interne displayet vekselvis symbolet for avstand
og mislykket måling. (Laserstrålemerket blinker.)
Mislyktes i å måle eller
kan ikke måle avstand.
Viser den målte
avstanden. (Mål 1)
Viser den målte
avstanden. (Mål 2)
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target
.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
5. Etter kontinuerlig måling vises de målte resultatene i 8 sekunder,
deretter slås strømmen av. Hvis du trykker på på/av-knappen når
strømmen er på (mens det interne displayet er aktivt), starter en
ny 8-sekunders måling.
Hvis du for eksempel måler avstanden til et flagg på golfbanen,
søker du etter flagget under målingen for å foreta en enkel måling.
Hvis det ikke er noen objekter mellom deg og flagget, er det
korteste resultatet avstanden til flagget.
4. Velge visningsenhet (standardinnstilling er yard)
1. Kontroller at det interne LCD-panelet er på.
2. Trykk og hold MODE-knappen nede (2 sekunder eller
lenger).
3. Når visningsenheten er skiftet, slipper du MODE-
knappen.
4. Når enheten er angitt, vil resultatene bli konvertert og
vist i den måleenheten du har valgt.
Meter [ ]Yard [ ]
6. Symbol for svakt batteri
Blinkende viser at batteriet er svakt og at det
bør skiftes. (Se Skifte batteri)
7. Bakgrunnslys
Bruk bakgrunnslyset for å se LCD-panelet når det er
mørkt.
Du kan slå bakgrunnslyset på eller av ved å trykke
kort på modusknappen (mindre enn 2 sekunder)
mens strømmen er på. Bakgrunnslyset kan også
slås av ved å slå av laseravstandsmåleren. Hvis du
gjør det, vil bakgrunnslyset være av når du slår på
laseravstandsmåleren igjen.
5. Avstandsdisplay
COOLSHOT benytter et system for prioritering av første
mål. Hvis det innhentes forskjellige resultater fra én
enkelt måling, vil den vise avstanden til nærmeste mål
på LCD-panelet.
Eks.: Ved måling av et tre foran et hus;
115 m (avstand til treet) vises.
Dette er nyttig hvis du spiller golf.
Tre Gjerde Hus
Avstand til mål 115 m 123 m 128 m
… 103 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Nikon Coolshot wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info