Bedienungsanleitung Nikon Laser 550A S (Seite 29 von 73) (Englisch, Französisch, Portugiesisch, Spanisch)

604470

Zoom out

Zoom in

Vorherige Seite

1/73

Nächste Seite

Others

Do not use the Nikon Laser 550A S for purposes beyond the limits of its stated accuracy.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules and to EU EMC directive. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

　•Reorientorrelocatethereceivingantenna.

　•Increasetheseparationbetweentheequipmentandreceiver.

　•Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Troubleshooting/Repair

If your Nikon Laser 550A S should require repair, please contact your local dealer for details regarding where

to send it. Before doing so, you are advised to consult the Troubleshooting Table below.

Symptom Check Points

Unit does not turn

on — LCD fails to

illuminate

Target range cannot

be obtained

[- - -] (“Cannot

measure”) appears

Closer target cannot

be measured

Target beyond a

certain distance

cannot be measured

•DepressPOWERbutton.

•Checkandreplacebatteriesifnecessary.

•Besurethatnothing,suchasyourhandorfinger,is

blocking the laser emission aperture and laser detector.

•Besurethatthelaseremissionapertureandlaserdetector

are clean. Clean them if necessary.

•Besurethatthetargetshapeandconditionisappropriate

to reflect the laser beam.

•Replacebattery.

•Besuretoholdtheunitsteadywhiledepressingthe

POWER button.

•Besurethetargetiswithinmeasuringrange(10-500m/11

- 550 yards)

•Besurethatnothing,suchasleavesorgrass,isbetween

the Nikon Laser 550A S and the target.

•Besurethatnothing,suchasleavesorgrass,isbetween

the Nikon Laser 550A S and the target.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nikon Laser 550A S Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info