Bedienungsanleitung Nikon Prostaff 3 REALTREE (Seite 7 von 33) (Englisch, Französisch, Portugiesisch, Spanisch)

604495

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

Operational summary

Caution—use of controls or adjustments or

performance of procedures other than those

specified herein may result in hazardous radiation

exposure

1. Install a battery in the battery chamber. (See

"Changing Batteries")

2. Rubber eyepiece cup

Eyeglass wearers: Roll up the rubber eyepiece cup

and use.

Non-eyeglass wearers: No need to roll up the rubber

eyepiece cup for use.

3. Diopter adjustment

Adjust diopter to obtain a clear image in the LCD.

First, rotate the diopter adjustment ring

counterclockwise until it comes to a complete

stop. Next, turn on the power to activate the LCD

when you look through the PROSTAFF 3. Rotate the

diopter adjustment ring clockwise until the display

comes into focus.

If the diopter is not adjusted to correspond to your

eyesight, you may not be able to clearly focus your

subject.

4. Measuring

Note: Depressing and holding down the POWER

button causes all symbols to be displayed in

the LCD panel. After you remove your finger

from the POWER button, the last-used setting

is displayed. (If you briefly press the POWER

button then remove your finger, the LCD panel

may display the last-used setting without

displaying all of the symbols. This is not a

malfunction or other problem.)

Before measuring, be sure to confirm unit setting.

5. Selecting display unit (default setting is yards.)

1. Confirm the internal LCD panel is on.

2. Press and hold the MODE button (more than two

seconds.)

3. When display unit has switched, release the MODE

button.

4. Repeat steps 2 and 3 until your desired mode is

displayed.

5. When you have completed setting, results will

be converted and displayed in the your selected

measurement unit.

Meter [ ]Yard [ ]

6. Distance display

The PROSTAFF 3 features Distant Target Priority

System.

When obtaining different results from a single

measuring operation, the PROSTAFF 3 will display

the distance to the farthest target on the LCD panel.

ex.) When measuring a tree standing in front of a

house;

"128m" (distance to the house) will be displayed.

This mode has applications for hunting in heavy

wooded areas.

7. Low battery indication

Flashing

indicates that the battery power is

low and battery should be replaced. (See "Changing

Battery")

Tree Fence House

Distance to Target 115m 123m 128m

POWER

LCD is illuminated

Align the reticle

with the target

POWER

appears

Indication

remains

illuminated

for 8 sec.

8 seconds pass without operation ＊

Power off: LCD indications disappear

Measure again

Fail to measure

Cannot measure

Successfully

measured

For continuous

distance

measurement (up

to 20 seconds),

keep button

depressed.

☆

☆【Continuous measurement mode】

Depressing the POWER button allows you to perform

continuous measurement for 20 seconds.

Appears while performing measurements.

＊ Power turns off automatically 8 seconds after the last

operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nikon Prostaff 3 REALTREE Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info