Bedienungsanleitung Nikon Prostaff 3 (Seite 6 von 33) (Englisch, Französisch, Portugiesisch, Spanisch)

604494

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

Changing batteries

•

Type of battery: 3V CR2 lithium battery

•

Battery condition indicators

: Battery has enough power for use.

: Battery is getting low.

flashing: Battery is low and battery should be replaced.

disappears: Battery is exhausted and should be replaced.

* Flashing battery mark

on the LCD warns that the battery should be replaced.

1 Open the battery chamber cover

Using the ball of the thumb, etc. in the recessed part of the battery chamber cover, rotate the cover

following the Open/Close arrow indicator.

It may not open easily due to its rubber packing for water resistance.

2 Replace the old battery with a new one

Install new battery with the [+] and [-] correctly positioned following the “Battery installation” indication

seal in the battery chamber. (Insert battery positioning the [+] pole towards the inside of the chamber.)

[The PROSTAFF 3 will not operate if the battery is installed incorrectly.]

3 Close the battery chamber cover

Align the Open/Close indicator with the white dot and insert the battery chamber cover. Using the ball

of the thumb, etc., turn the cover in the opposite direction to the arrow indicator. It may not close easily

due to the rubber packing for water resistance, but continue to turn it all the way until it stops. Confirm

that the cover is securely closed.

•

Battery life

Continuous operation: Approx. 10,000 times (at 20°C)

Target focusing, measurement, and automatic power off are included in a single cycle. This figure may differ

according to temperature, and other factors such as target shape, colour, etc.

* The PROSTAFF 3 comes with a 3V CR2 lithium battery. However, due to natural electric discharge, the life of the battery will

likely be shorter than that noted above.

* Replace battery if the PROSTAFF 3 is ever submerged in water or if water enters in the battery chamber.

1. 『』 - Target mark/Laser irradiation

『

』 - Aim at the target. Position the target at the center of the reticle.

『』 - Appears while the laser is being used for a measurement.

(Remains present during single measurement and continuous

measurement.)

Warning: Do not look into the objective lenses when this mark is shown.

2．『

』: Distance/measurement status display

Digitally indicates measured distance in meters/yards. Also indicates measuring

status such as “Measurement in progress”, “Measurement unsuccessful” or “Unable

to measure.”

(Distance)

Display of results: ( ≧ 100m/yards) e.g. 234 meters = 『

』

Display of results: ( ＜ 100m/yards) e.g. 76.5 yards = 『

』

『

』 - Now measuring

『

』 - Failure to measure or unable to measure distance

3. 『

』

Display Units

『

』Indicates distance being measured in meters.

『

』Indicates distance being measured in yards.

4. 『

』- Indicates battery condition. (See "Changing Batteries")

* Although the LCD was produced using the most advanced technology, it is impossible to eliminate dust

completely. When using this product, the LCD is magnified by high magnification of the eyepiece lens and

dust may appear as a defect. It will not, however, affect measurement accuracy.

Internal display

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nikon Prostaff 3 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info