570912
14
Zoom out
Zoom in
Vorherige Seite
1/89
Nächste Seite
5
Precautions for Use
Precautions for Use
Observe the following precautions to ensure that the scanner always produces the best pos-
sible results.
Check the status LED
Do not turn the scanner off or insert or remove fi lm holders while the status LED is blinking.
Do not use other IEEE 1394 (Firewire) devices or turn them on or off while the status LED is blinking.
Do not connect or disconnect USB or IEEE 1394 (Firewire) cables while the status LED is blinking.
Do not operate camera control software for digital cameras connected via USB while the status LED is
blinking.
Connecting the scanner
Connect the scanner directly to the computer. The scanner may not function as expected when con-
nected to an IEEE 1394 hub or adapter.
The scanner may not function as expected when used together with other IEEE 1394 devices. Should
the scanner not function as expected, use the scanner with all other IEEE 1394 devices disconnected.
Do not connect two or more scanners to the computer simultaneously.
Protecting fi lm
Before scanning fi lm, remove dirt and dust with a blower. This will not only keep the fi lm free of
scratches but will also help prevent scanning errors and malfunctions.
Remove fi ngerprints with a soft, dry cloth, being careful not to scratch the fi lm.
Remove fi lm from the holder after scanning. Storing fi lm in the holder could damage the fi lm.
The fi lm base and emulsion will deteriorate if exposed to high temperatures or humidity. Be sure tem-
perature and humidity are within the limits given below.
Sudden changes in temperature and humidity, even when within the limits stated below, can cause
condensation on the fi lm. Check before use to ensure that no condensation is present. If condensa-
tion has occurred, leave the fi lm out until it dries. Condensation can damage the fi lm during inser-
tion.
The operating environment for the scanner is as follows:
Temperature: +10 – +35 °C (+50 – +95 °F)
Humidity: 20 – 60%
When the scanner is not in use
Remove the fi lm holder and turn the scanner off when not in use.
14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

nikon-super-coolscan-9000-ed

Suche zurücksetzen

  • Nach dem Prescan sehe ich nur ein Bild anstatt drei?
    Eingereicht am 5-4-2018 13:27

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Nikon Super Coolscan 9000 ED wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Nikon Super Coolscan 9000 ED

Nikon Super Coolscan 9000 ED Bedienungsanleitung - Deutsch, Holländisch, Italienisch - 263 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info