Bedienungsanleitung Nilfisk-ALTO ATTIX 791-2M B1 (Seite 5 von 16) (Englisch)

608943

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

ATTIX 791-2M/B1

Precautions and safety

regulations when using the

vacuum cleaner

Before start-up

Inspect power cord regularly

to detect signs of damage, e.g.

cracks or ageing.

If the power cord is damaged,

it must be replaced by Nilfisk-

Alto-Service or an electrician to

avoid danger before use of the

vacuum cleaner is continued.

Use only the type of power

cord specified in the operating

manual.

Do not damage the power cord

(e.g. by moving over it or pulling

or crushing it).

Disconnect the power cord by

pulling the plug only (do not pull

or tug the power cord).

Inspect the vacuum cleaners to

ensure that they are in proper

condition. Plugs and couplings

in power cords must at least

have splash protection.

Never use the vacuum cleaner if

the filter element is damaged.

Picking up liquids

If foam develops or liquid

emerges, stop work immediately

and empty the dirt tank.

Regularly clean the float that

limits the water level and check

it for damage.

See section 5 for information on

handling liquids and (hazard-

ous) dust.

Electrical components

Check the rated voltage of the

vacuum cleaner before con-

necting it to the mains supply

system. Ensure that the voltage

shown on the rating plate cor-

responds to the voltage of the

local mains power supply.

If you are using an extension

cord, use only those specified

by the manufacturer or higher

quality ones (see section 9.4

„Technical data“).

It is recommended that the

vacuum cleaner should be con-

nected via a residual current

circuit breaker. This stops the

supply of electricity if the leak-

age current to earth exceeds 30

mA for 30 ms or it has an earth

tester circuit.

When using an extension lead,

check the minimum cross-sec-

tions of the cable:

Cable length

Cross section

<16 A <25 A

up to 20 m

ø1.5mm² ø2.5mm²

20 to 50 m

ø2.5mm² ø4.0mm²

Use the cleaner only if it is cer-

tain that no active sources of

ignition can be sucked in.

Conductive extraction equip-

ment, e.g. extraction hoods on

machines and conductive parts

of machining equipment (e.g.

equipment in protective class

II) that are not earthed through

the cleaner, must be earthed in

some other way to prevent elec-

trostatic charges.

The cleaner is not suitable for

extraction on machining equip-

ment in operation that could

produce sources of ignition.

When dust removers are used,

the rate at which air is ex-

changed in the room must be

adequate if the exhaust air from

the vacuum cleaner is blown into

the room (please observe regu-

lations valid in your country).

Before starting work, the operat-

ing staff must be informed on

– use of the vacuum cleaner

– risks associated with the ma-

terial to be picked up

– safe disposal of the picked

up material.

It must be assured that dust not

accumulate on the appliance by

regular cleaning.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nilfisk-ALTO ATTIX 791-2M B1 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nilfisk-ALTO ATTIX 791-2M B1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info