Bedienungsanleitung Nilfisk-ALTO Autobooster (Seite 5 von 33) (Englisch)

609320

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

AUTO BOOSTER

Original Instructions

cleaned and harming the envi-

ronment.

Do not clean sensitive surfaces

made of rubber, fabrics or the

like with the zero nozzle. With

the ﬂ at jet nozzle keep a dis-

tance of at least 15 cm to the

surface to be cleaned.

Do not use the machine if the

electric cable or the high-pres-

sure hose are damaged.

Do not cover the machine dur-

ing operation or use it in a room

without adequate ventilation !

If any of the machines over-

load protection devices trips

(machine stops unintended),

release the trigger of the spray

handle. Lock the spray handle

with locking device and turn

the start/stop switch to position

„OFF“.

Refer to section “6 Trouble

Shooting”.

Never start the cleaner without

water supply. Even a short wa-

ter deﬁ ciency can damage the

sleeves of the pump.

Operation

Avoid damage to the electric

cables such as squeezing, pull-

ing, knots etc. and keep them

away from sharp or hot objects.

Avoid damage to the high-pres-

sure hose such as running over

by vehicles, squeezing, pulling,

knots/kinks etc. and keep it

away from oil and sharp or hot

objects, as such may cause the

hose to burst.

The cleaner can be used in

zones classiﬁ ed as ZONE 2.

Important! Never use the

machine in an environment

where there could be a danger

of explosion (according to EN-

50014).

Important! When the system

has been in operation and

thereafter stopped, there might

still be a working pressure in

the pipeline and high-pressure

hoses. Therefore you should

pay special attention to the fol-

lowing:

• Never dismount the high-

pressure hose from the

machine during operation.

Disconnect the machine and

relieve the high-pressure

hose of pressure prior to

dismounting.

• Never dismount the high-

pressure hose from the

outlet point before it has

been securely closed and

the high-pressure hose has

been relieved of pressure.

• Prior to any service inter-

ference in the machine it

should be disconnected and

the system relieved of pres-

sure by activating the trigger

of the spray handle.

Repair and Maintenance

Only carry through the mainte-

nance operations described in

the operating instructions. Only

use original Nilﬁ sk-ALTO spare

parts.

Do NOT make any technical

modiﬁ cations to the high-pres-

sure hot water washer.

Warning! High-pressure hoses,

nozzles and couplings are

important for the safety when

operating the machine. Only

use the high-pressure hoses,

nozzles and couplings pre-

scribed by Nilﬁ sk-ALTO!

For major repairs, please con-

tact your nearest Nilﬁ sk-ALTO

service organisation.

Mains power connection

This product is intended for

stationary installation only

and is supplied without a

power cord! Only let an au-

thorized electrician connect

the machine to the mains

supply !

The following points must be

observed:

• Check that the voltage

stated on the data plate

corresponds to your mains

voltage.

• Make sure that the power

cord contains the right

number of wires (including

ground wire) and that each

wire has the right dimen-

sions to carry the load (am-

perage) stated on the data

plate of the machine.

• Make sure that the instal-

lation (cables, connection

points and fuses) is correctly

dimensioned for the load of

the machine - refer to the

data plate of the machine.

If not required by local legis-

lation, we strongly recom-

mend you to connect the ma-

chine to a power source with

a Residual Current Device

(HPFI type B) which will dis-

connect the power supply if

the leakage current exceeds

30 mA ! This Residual current

device is necessary because

of an inverter in the machine.

See section “3.5 Mains power

connection” for further instruc-

tions.

Only let a qualiﬁ ed electrician

maintain the electric installation.

Safety Devices

Safety Valve

The pressure side of the high-

pressure pump is ﬁ tted with a

safety valve. This valve leads

the water back to the suction

side of the pump when the

spray handle is closed or if a

nozzle is blocked.

The safety valve is adjusted

and sealed by the producer.

THIS ADJUSTMENT MUST

NOT BE CHANGED !

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nilfisk-ALTO Autobooster Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nilfisk-ALTO Autobooster

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info