Bedienungsanleitung Nilfisk-ALTO MULTICLEANER 7-53 (Seite 23 von 29) (Englisch)

609307

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

MULTICLEANER 7-53

Original Instructions

9.2.2 Oil change

Lubrication must be made each 200 operation hours.

Shafts for the driving and supporting wheels of the MULTICLEANER

must be lubricated with ordinary lubricant grease. Positioning bolts,

quick connectors, movable segments in the arm, hinges and the en-

try of the tow handle must be lubricated with a lubricant containing

teflon. The easiest way out will be to use a spray with the lubricant.

The pump oil must be replaced after max. 500 hours of operation,

however at least each 6 months. If water in the oil is observed, re-

place the oil and refill with oil of the type Castrol Alphasyn T 150.

9.2.3 Inspection of long

distance nozzle

Normally the long distance nozzle can only be checked visually as it

requires a special equipment to measure it up. If the spray is very

diffuse and not concentrated as usually, the reason may be that it is

either clogged up or worn.

9.2.4 Cleaning of filter in dirt

collector

Before the water valve there is a water filter with a stainless strainer

with a mesh size of 0.25 mm filtering out impurities before they

reach the water valve.

Clean/check the water filter each week or for each 100 operating

hours. This is easily done by using a ratchet wrench with a 24 mm

head and a long adapter and loosening the nut for the dirt collector

from below. If not possible an alternative solution will be to loosen

the union nut of the 3/4" union, remove the hose clamp and the

water hose between the flow switch and the motor/pump unit and

then dismount the tube support. Now the complete unit with compo-

nents for the water supply can be turned around and the nut for the

strainer dismounted.

Rinse/clean the strainer and remount in reverse order. If the strainer

cannot be cleaned, it is possible to buy one separately. It is not

necessary to replace the complete dirt collector.

9.2.5 Inspection of pressure

in tyres

The air pressure in the pneumatic tyred wheels must be approxi-

mately 2.5-2.8 bars. There must be a clearance between the con-

crete floor and the underside of one set of the supporting wheels of

2.5-3 cm, when the MULTICLEANER rests on the two other set of

wheels.

9.2.6 Banjo bolt at the

nozzle head

O-rings and back-up-rings on the banjo bolt at the nozzle head must

be lubricated each 100 operating hours and replaced at regular in-

tervals.

9.2.7 Lubrication

9.2.8 Inspection of initial

tension of the springs

in the cable reel

Inspection of the initial tension of the cable:

If 5 metres of cable have been laid out, the springs in the reel must

provide a tractive effort of 4 kg at a minimum corresponding to a

tractive effort of approximately 8.5 kg at a layout of 30 metres.

Let a Nilfisk-ALTO service technician set the initial tension of the

cable reel.

The life of the springs in the cable reel is approximately 5,000 hours

and the life of the collector ring is approximately 12,000 hours.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nilfisk-ALTO MULTICLEANER 7-53 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info