Bedienungsanleitung Nilfisk C 110.4 (Seite 9 von 17) (Englisch)

505724

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

9Original Instructions



When connecting the machine to operate from pressure less water supplies – always use ad-

ditional ﬁ ltering to secure that impurities are not sucked in. Hose length should be max. 3 meter

and of minimum ½".

To meet these requirements, Nilﬁ sk recommends that you use the original Nilﬁ sk suction hose

kit.

The Machine is designed for suction up to 50 cm above water surface.

• Position the machine at max. 0.5 meter above water surface. Detach the high pressure hose

from the outlet.

• Ensure that the inlet ﬁ lter is in position and attach the suction hose kit, secure tight connec-

tion to the inlet.

• Turn on the machine, pressing the start/stop switch (1) into position "I".

• Wait until a steady jet exits the outlet.

• Switch off the machine and attach high pressure hose (4), spray handle, lance and nozzle.

• Start the machine again and activate the spray handle.

4.4 Starting the high pressure washer

IMPORTANT!

Connecting to mains power supply

The voltage and frequency of the machine (see model tag (14)) must match the voltage and

frequency of the power supply.

B9 Insert the power plug into power supply socket.

B10 Turn on the water.

B11 Release the trigger lock (7a). Remember to unplug, turn off the high pressure washer and

lock the trigger, when leaving the high pressure washer unattended

B12 Activate the trigger of the spray handle and let the water run until all air has escaped from

the water hose.

B13 Turn on the machine, pressing the start/stop switch into position “I”.

B14 Activate the trigger of the spray handle. When releasing the trigger of the spray handle,

the machine automatically stops. The machine will start again when you reactivate the

trigger of the spray handle.

5 After using the pressure washer

See the pictorial quick reference guide – storing the high pressure washer.

The high pressure washer should be stored in a frost free room! Should the machine by a mis-

take be frozen, it will be necessary to check it for damages.

5.1 Stopping the high pressure washer

C1 Shut off the water supply and activate the trigger of the spray handle and let the machine

run until no more water runs out of the nozzle. This will wash out water hose, high pres-

sure hose, spray lance and nozzles.

C2 Stop the machine, pressing the start/stop switch into position “0”.

C3 Unplug the machine from the power supply socket and wind up the electrical cable (5)

and place it on the holder (16).

C4 Rinse the spray lance, nozzles and the foam sprayer after use.

C5 Place spray handle, lance, nozzles, foam sprayer and other accessories in the holders on

the high pressure washer.



Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nilfisk C 110.4 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nilfisk C 110.4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info