Bedienungsanleitung Nilfisk D-PG 130.4 X-TRA (Seite 12 von 23) (Englisch)

586799

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

12 Original Instructions

4.3 Water Connection

IMPORTANT!

Connecting to pressurized water supply

The inlet water max. pressure is 1 MPa/10 bar and the max. temperature is 60°C – see rating

plate. An ordinary ½" garden hose of min. 10 m and max. 25 m will be suitable.

B6 Check that the ﬁ lter is ﬁ tted in the water inlet pipe and that it is not clogged up.

B7 Connect the water hose to the water supply by means of the quick connector. Turn on the

water.

Connection to the drinking water mains according to national and local regulations.

Let the water run through the water hose before connecting it to the machine to prevent sand

and dirt from penetrating the machine.

B8 Turn off the water and connect the water hose by means of the quick coupling to the wa-

ter inlet.

Connecting to pressure less water supply

The machine can also operate in suction mode, meaning that you can connect the machine to

e.g. rainwater vessels, rivers, lakes and cisterns etc. When taking in water from non drinking

water mains the backﬂ ow preventer is not needed.

When connecting the machine to operate from pressure less water supplies – always use ad-

ditional ﬁ ltering to secure that impurities are not sucked in. Hose length should be max. 3 meter

and of minimum ½".

To meet these requirements, Nilﬁ sk recommends that you use the original Nilﬁ sk suction hose

kit.

The Machine is designed for suction up to 100 cm above water surface.

• Position the machine at max. 1.0 meter above the water surface. Detach the high pressure

hose from the outlet.

• Ensure that the inlet ﬁ lter is in position and attach the suction hose kit, secure tight connec-

tion to the inlet.

• Turn on the machine, turning the start/stop switch (1) to position "I".

• Wait until a steady jet exits the outlet.

• Switch off the machine and attach high pressure hose (4), spray handle, lance and nozzle.

• Start the machine again and activate the spray handle.

4.4 Starting the high pressure washer

IMPORTANT!

Connecting to mains power supply

The voltage and frequency of the machine (see model tag (14)) must match the voltage and

frequency of the power supply.

Connecting the high pressure washer to a supply system, the max allowed impedance is =

0,29+j0,18 (Zmax). Consult with the supply authority that the equipment is connected only to

a supply of that impedance or less.

B9 Insert the power plug into power supply socket.

B10 Turn on the water.

B11 Release the trigger lock (7a). Remember to unplug, turn off the high pressure washer and

lock the trigger, when leaving the high pressure washer unattended

B12 Activate the trigger of the spray handle and let the water run until all air has escaped from

the water hose.

B13 Turn on the machine, turning the start/stop switch to position "I".

B14 Activate the trigger of the spray handle. When releasing the trigger of the spray handle,

the machine automatically stops. The machine will start again when you reactivate the

trigger of the spray handle.



Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nilfisk D-PG 130.4 X-TRA Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nilfisk D-PG 130.4 X-TRA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info