Bedienungsanleitung Nilfisk GM 80 C (Seite 17 von 48) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

72023

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

8 Suction with dust bag

The cleaner is supplied with a two-ply self-locating dust bags.

To release the container, unfasten the two latches and lift off

the upper part with the motor/filter section. Fix the dust bag as

follows:

1 Pierce the dust bag’s perforation and place it in the lower

container.

2 Pull the dust bag plastic plate over the suction inlet with

both hands. Unfold the dust bag carefully. Replace the top

container and lock the two latches.

Note

The suction efficiency depends on the size and quality of the

dust bag. Use original Nilfisk bags only. If non-Nilfisk dust bags

are used, and airflow restricted, overheating of the motor and

subsequent damage may result.

9 Exhaust filter

Exhaust filters is used when absolutely clean exhaust air is

necessary. The exhaust filter is mounted on to the motor in

place of the diffuser. The exhaust filter is easily fitted and the

fllter element is replaceable. A special handle is delivered

together with the exhaust filter.

10 Blowing attachment

Mounting

Remove the diffuser and sound absorber (see page 2)

Place the blowing adaptor 11562000 on the motor. Each one

is kept in place by handle of the motor.

Fit the blowing attachment into the motor blowing adaptors.

Before connecting a hose make sure that it is clean - place its

open end in the container inlet for a moment with the motors

running and shake it.

Maintenance

Always keep the cleaner in a dry place. The bearings in the

motor are pregreased and designed for continuous heavy

work.

Depending on the number of running hours the dust filter

should be replaced.

For details of service or maintenance please contact NILFISK

directly.

Rating Plate

The model and serial number of your machine are shown on

the ratingplate on the machine. This information is needed

when ordering repair for the machine. Use the space below to

note the model and serial number og your machine for future

reference.

Model

Serial number

Year of manufacture

Powering voltage

Trouble-shooting

• the motor will not start

- a fuse may have blown and needs replacing.

- the cable or the wall socket may be defective and needs

checking.

• the suction power is reduced

- the dust bag may be full and needs replacing,

see page 3.

- the filter may be clogged and needs shaking,

see page 3.

• the vacuum cleaner stops Only USA and Canada

- the thermal cut-out has switched off the motor as a result

of an obstruction of the hose, wand or nozzle.

- Start by remove the electrical main cord from the power

outlet.

- When the machine is unplugged remove the cause

of the obstruction.

- Wait at least 5-10 minutes.

- Put back the electrical cord to the power outlet.

- When the motor is cool, it will automatically start again.

• the motor will not stay locked in position on the

container Only 90

- The red locking lever in the container top is in the wrong

position. Push the lever in the direction of the arrow.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nilfisk GM 80 C Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info