Bedienungsanleitung Nilfisk gm 90 (Seite 15 von 48) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

316935

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

IMPORTANT WARNINGS

1. This machine is also suitable for normal housekeeping

purposes in hotels, schools, hospitals, factories, shops

and offices.

2. This machine is not suitable for picking up health

endangering dust.

3. This machine is for dry use only and shall not be used or

stored outdoors in wet conditions. Store indoors between

max. 60 C (degrees centigrade) and min. 0 C (degrees

centigrade).

4. The machine for vacuum dry dust must not be used for

the suction of water or other liquids.

5. The machine must not be used for picking up combustible

or explosive materials, nor should it be used in an

explo sive atmosphere.

6. Under no circumstances should the machine be used for

picking up hot material. In particular the machine must not

be used for cleaning open and closed fireplaces, ovens or

similar that contain warm or glowing ashes.

7. The machine must not be used if the electrical cord

shows any sign of damage. Regularly inspect the cord for

damage, in particular if it has been crushed, shut in a door

or run over.

A detachable supply cord with integrally molded plugs

must not be repaired. It has to be replaced by a new

supply cord supplied by NILFISK if the cable or plugs are

damaged.

8. The machine must not be used if it is faulty.

9. Do not unplug by pulling on cord. To unplug, grasp the

plug, not the cord.

10. When repairing or replacing the cord, the same type of

cord as originally supplied with the machine must be used.

This cord can be supplied by NILFISK.

11. The plug must always be removed from the socket outlet

before starting any service work of the machine or the

cord.

12. Repair of the electrical unit with motor or the cord must

only be carried out by a skilled or instructed person after

having disconnected the main switch installed prior to the

machine or after having removed the plug from the current

socket.

13. No changes or modifications to the mechanical or

elec trical safety devices should be made.

Instructions for use

Before the vacuum cleaner is ready for use, the hose must be

fitted to the curved tube as described under point 5.

Before using the vacuum cleaner make sure that the voltage

shown on the rating plate corresponds with the mains voltage.

The vacuum cleaner is supplied with a paper dust bag already

in place. Never use the vacuum cleaner without a properly

fitted dust bag. The procedure for replacing the dust bag is

described under point 8.

1 Starting / stopping

1 Place the appliance plug of the cable in the motor socket.

Plug the cable into the wall socket.

Press button 1. to start the motor

Press button 1. again to stop it.

After cleaning, unplug the cable from the wall socket.

Detaching the power cord

To prolong the life of your cord, detach it from the motor each

time after cleaning, roll it up loosely and store it.

2 Note

Do not roll the cord tightly around the motor as this will place a

strain on the cord and considerably shorten its life.

Thermal cut-out protection

(Only USA and Canada)

The vacuum is provided with a thermal cut-out protection

mechanism. This prevents the motor from overheating if a

blockage should occur. If this occur start by removing the

electrical cord from the power outlet. Then remove the cause

of the blockage to allow free air passage. Wait at least 5-10

minuttes. Then put back the electrical cord to the power outlet.

When the motor is cool, it will automatically start again.

3 Micro-Static Filter

The grey Micro-Static filter on the top of the motor attracts and

retains micro-particles efficiently. In order to ensure a constant

cleaning of the exhaust air and to avoid overheating of the

motor, it is essential that the filter is replaced regularly. The

Micro-Static filter should be replaced after approx. 50 hours

use, equivalent to one year of domestic use.

Replacing

1Turn the two screws with a coin until their slots are vertical.

2 Release the handle by a gentle downward pressure at its

centre. Press until both ends spring out from the motor

recess.

3 Lift off the exhaust grill and the filter. The sound absorbent

material must remain on top of the motor.

4 Remove the grey filter and mount the new one. Replace the

grill. Locate the handle into position and lock it by turning the

screws until their slots are horizontal.

4 Hose connection

Insert the bayonet coupling into the suction inlet, and lock it

in place by turning it clockwise. Reverse this procedure to

disconnect the hose.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nilfisk gm 90 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info