Bedienungsanleitung Nilfisk GU 12 SMU (Seite 11 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

454199

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

The pre ﬁ lter catches any dirt spilled from the bag, before it can enter

the vacuum motor. The ﬁ lter is located below the bag.

Clean the ﬁ lter every third time that the bag is changed (more often in

very dusty applications).

To clean/replace the Pre Filter.

1. Disconnect the power cord from the electrical outlet. Then

push the Dust lid button (16) in and remove the dust lid (5).

2. Grasp at the ﬁ lter holder and pull the holder out from the

Dust compartment.

3. Remove the dirty ﬁ lter from the ﬁ lter holder and replace with a

new pre ﬁ lter.

The pre ﬁ lter may also be washed. Wash it in warm

water. Let the ﬁ lter dry completely before putting it back into

the ﬁ lter holder.

4. This machine is also equipped with a deodorizer pad (an anti

smell). It´s a located in the pre ﬁ lter holder.

Replace it to a new deodorize pad when the function begins to

fade.

5. Put back the new/washed ﬁ lter into the holder. Then put back the

holder with ﬁ lter in place in the bag housing.

6. Fit the two notches of the back cover to the two slots at the lower

part of the bag housing, and push the back cover back

in place at the housing.

IMPORTANT !

Never operate the machine without the pre-ﬁ lter in place.

1. Disconnect the power cord from the electrical outlet.

Push the Filter Cover Latch

(19) downwards so that the Filter

Cover

(18) is released.

2. Remove the cover with the ﬁ lter, from the cleaner.

3. Remove the used and dirty exhaust ﬁ lter.

4. Insert a new exhaust ﬁ lter to the ﬁ lter cover.

5. Snap the Filter Cover back in place on the cleaner.

CHANGING THE EXHAUST FILTER

Unplug the Power Cord from the electrical outlet.

2. If the Dust Bag Full” Indicator (15) not has been lightened

during operation - the dust bag still has ﬁ lling capacity. Open

the dust housing cover to ensure that the dust bag is not

full, replace if necessary. See also separate instructions for

replacing the dust bag. Clean the bag housing, if necessary.

Wind up the cord (starting from the machine inlet side).

Store the cord at the hook at the Dust lid cover and the hook

at the handle.

Check the brush house. Remove any built-up carpet ﬁ bers or

debris from the brush and the brush housing.

6. Store the machine indoors in a clean, dry place.

CLEANING OR CHANGING THE PRE FILTER

AFTER USING THE MACHINE

IMPORTANT !

Never operate the machine without the Exhaust Filter in

place at the machine.

823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 11823 0102 000 Instruction for use GU 305, GU 355, GU 355 DUAL, GU 455 DUAL EU 1.indd 11 2008-04-17 09:36:352008-04-17 09:36:35

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nilfisk GU 12 SMU Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info