Bedienungsanleitung Nilfisk Meteor (Seite 4 von 7) (Englisch)

586804

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

Meteor

Original Instructions

grasping the plug, not by pulling at the cable.

Activate the cable rewinder.

3.2 Connecting hose, tube and

nozzles

1. Insert the hose connector into the suction inlet.

2. Connect the bent tube to the tube.

3. Connect the tube to the nozzle.

4. The tube is telescopic and can be adjusted

to your height. Push the adjusting button to

extend the tube and pull back to shorten to

desired length.

Container full indication

On the control panel a lamp is placed, where you

will receive notiﬁ cation, when the container is full

or the suction is degraded otherwise.

The dust container must be emptied if the lamp

is constantly on when the machine is operating

at maximum power and the nozzle is raised from

the ﬂ oor.

3.3 Releasing and emptying of dust

container

The dust container can be separated from the

machine for emptying. Simply release the dust

container from the machine by pressing the but-

tons on the dust container handle (see illustration

below) and pull the dust container upwards. The

dust container can now be emptied in a dustbin,

by pressing the lever marked “Push”.

3.4 Changing the exhaust ﬁ lter

Open the cover for the exhaust ﬁ lter, as seen in

the overview image (page 2), replace the ﬁ lter

with a new one and close the cover again.

3.5 Washing/exchanging the HEPA

ﬁ lter

You will have access to the HEPA ﬁ lter when you

have released the dust container.

Rinse the inside of the ﬁ lter using lukewarm

tap water. Do not use any cleaning agents and

avoid touching the ﬁ lter surface. Tap the ﬁ lter to

remove the excess water. Make sure to let the

ﬁ lter dry before putting it back into the vacuum

cleaner.

If necessary, exchange the ﬁ lter.

Please note that the machine will not function

without a HEPA ﬁ lter.

3.6 Parking the tube and nozzle

There are two grooves for parking. One located

on the underside to use when machine stands on

the back, and the other on the back to use when

the machine is standing on the wheels.

3.7 Thermal fuse

The machine is ﬁ tted with a thermal fuse, which

prevents the machine from overheating. If the

thermal fuse blows, the machine automatically

switches off the motor and must cool before it

can be started again.

Restart

1. Turn off the machine and unplug from the wall

socket.

2. Make sure that nothing blocks the air ﬂ ow

through the bent tube, hose, tube, nozzle or

ﬁ lters.

3. Let the machine cool.

4. Plug in the machine again and push the start

button. The machine will not start until cool

enough. If the machine does not start turn it

off and unplug. Try again in a while.

4. Cleaning tips

Adjust the suction power by means of the power

regulation or the sliding valve on the bent tube.

Upholstery nozzle (13)

Use the upholstery nozzle for upholstered furni-

ture.

Brush nozzle (14)

Use the brush nozzle for curtains and window

sills.

Hard ﬂ oor nozzle (15)

Use the nozzle for hard ﬂ oors.

On/off

switch

Adjust suction power

Cable

rewinder

Container full

indication

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nilfisk Meteor Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nilfisk Meteor

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info