Bedienungsanleitung Nilfisk Performer 250 (Seite 6 von 26) (Englisch)

586823

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

2.1 Fitting the wall bracket

Position the holder so that there is plenty of space above and

below the place where the vacuum unit is to be located. Make

sure there is a minimum of 500 mm free space above the

container. Mark the positions for the four screw holes with a

pen or similar. Then select appropriate screws and, if neces-

sary, wall plugs for the type of wall surface to which the brack-

et is to be attached. Drill the four holes for the wall bracket.

The diameter of the screw holes in the holder is 5 mm. Fit the

wall bracket with the large opening pointing upwards, see Fig.

1. Tighten the screws so that the holder is held ﬁ rmly in place

(screws provided).

2.3 Connecting the machine

The machine is connected with the suction pipe in the uppermost position and the exhaust

pipe in the lower position.

This connection should not be glued but can be taped when the unit is serviced at a later

date. The suction pipe socket can be ﬁ tted to two different points depending on the direc-

tion in which you would like to install the pipe system.

To relocate the suction pipe socket, you need to do the following:

1. Release the suction pipe socket by unscrewing the four combination Torx screws with a

Torx T20 or an ordinary screwdriver, Fig. 3.

2. Pull the socket out of the machine, see Fig. 4.

3. Loosen the plug blanking off the outlet to which you intend moving the suction pipe

socket. Unscrew the four combination Torx screws. Remove the blanking plug from the

machine.

4. Adapt (move) the suction pipe socket to the new outlet. NB! The socket is marked ”Up”.

Make sure the socket is ﬁ tted with ”Up” uppermost. Fasten the socket by ﬁ tting and

tightening the four screws, Fig. 5.

5. Fit the blanking plug to the outlet previously occupied by the suction pipe socket. Use the four screws to hold it in place.

The exhaust pipe must be ﬁ rmly attached to the wall to ensure its connection with the socket does not loosen. Remember

that you will need to be able to turn the bent pipe in different directions to ensure a suitable pipe layout. Then connect up

the exhaust pipe and mufﬂ er, Fig 6. Fit the central vacuum cleaner so that the exhaust pipe is as short as possible, max.

5 metres. Take the surroundings into consideration when positioning the exhaust. For this reason, you should always ﬁ t a

mufﬂ er.

For additional information concerning the assembly and installation of the pipe system and low-current lead, please refer to

the separate assembly instructions supplied with the pipe package.

2 Vacuum unit Supreme 100 assembly instructions

2.2 Locating the vacuum cleaner on the

wall bracket

Position the vacuum unit so that the wall bracket is directly

above the wall bracket, see Fig. 2. Lower the machine down

on to the wall bracket. Make sure the corresponding bracket

on the machine is held ﬁ rmly in place by the wall bracket.

Fig. 1 Fig. 2

Fig. 3 Fig. 4 Fig. 5

Exhaust

Inlet

Fig. 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nilfisk Performer 250 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nilfisk Performer 250

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info