Bedienungsanleitung Nilfisk SC2000 (Seite 69 von 116) (Deutsch, Englisch, Holländisch, Französisch)

787649

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

INSTRUCTIONS FOR USE ENGLISH

9100000383 - SC2000 11

01/2015

revised 07/2017

USE/OPERATION

WARNING!

On some points of the machine there are some adhesive plates indicating:

–DANGER

–WARNING

–CAUTION

–CONSULTATION

While reading this Manual, the operator must pay particular attention to the symbols shown on the plates (see Visible Symbols On

The Machine paragraph).

Do not cover these plates for any reason and immediately replace them if damaged.

MAGNETIC SMART KEY

A magnetic smart key (52) is required to start the machine. If the start switch (42) is pressed and the key is not in the key reader

(41), the display will turn on temporarily and it will show a key insertion request, then it will turn off.

There are two different magnetic smart keys:

1. “User” key (blue) for scrubbing/drying operations and basic information.

2. “Supervisor” key (yellow) for accessing additional features (see the Supervisor key paragraph in Maintenance chapter).

BATTERY CHECK/SETTING ON A NEW MACHINE

WARNING!

The electric components of the machine can be seriously damaged if the batteries are either improperly installed

or connected.

The batteries must be installed by qualiﬁ ed personnel only.

Check the batteries for damage before installation.

Handle the batteries with great care.

The machine requires 2 12 V batteries, connected according to the diagram shown in Figure 1.

The machine can be supplied in one of the following modes:

Batteries already installed on the machine

1. Ensure that the battery connector (6) is connected.

2. When ﬁ rst using the machine with new batteries, perform a full charging cycle (see the procedure in Maintenance chapter).

Without batteries

1. Buy appropriate batteries (see “Technical Data” paragraph). For battery choice and installation, apply to qualiﬁ ed battery

Retailers.

2. Set the machine according to the type of batteries installed as shown in the Super User key section of the Maintenance

chapter.

BATTERY INSTALLATION

Battery Installation

1. Remove the user key (52).

2. Disconnect the battery connector by pressing the

emergency push-button (5).

3. Lift the cover (18) and check that the recovery tank (17) is

empty, otherwise empty it with the drain hose (26).

4. Close the cover (18).

5. Grasp the handle (35) and carefully lift the recovery tank

assembly (17).

6. The machine is supplied with cables suitable to install 2 12

V batteries.

7. Carefully lift the batteries until the relevant compartment,

then place them properly.

8. Route and install the battery cable as shown in Figure 1,

then carefully tighten the nut on each battery terminal.

9. Place the protection cap on each terminal, then connect

the battery connector (6).

10. Disengage the support rod (36), then grasp the handle (35)

and carefully lower the recovery tank assembly (17).

12 V

BACK

FRONT

Figure 1

P100863

Battery Charging

11. Fully charge the batteries (see the procedure in

Maintenance chapter).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nilfisk SC2000 Seite 69

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info