Bedienungsanleitung Nilfisk SC2000 (Seite 72 von 116) (Deutsch, Englisch, Holländisch, Französisch)

787649

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

ENGLISH INSTRUCTIONS FOR USE

14 SC2000 - 9100000383 01/2015

revised 07/2017

MACHINE START AND STOP

Starting the machine

1. Prepare the machine as shown in the previous paragraph.

2. Place the user key (52) in the key reader (41), then press the push-button (42) to start the machine.

3. In the ﬁ rst 2 seconds after machine start-up, the display (51) indicates the machine working hours (51-A) and the type of

batteries installed (51-B).

NOTE

Check the battery charge level.

When the display shows at least one segment of the battery symbol (51-C) which is on but not ﬂ ashing, the machine is

ready for use.

When the battery symbol (51-C) shows just one segment ﬂ ashing, the batteries have to be charged (see the procedure in

Maintenance chapter).

4. Drive the machine to the working place, by starting it with both hands on the steering wheel (1) and by pressing the drive pedal

(2).

The drive speed can be adjusted from zero to maximum speed according to the pressure on the drive pedal (2).

5. The forward/reverse gear is selected with the relevant lever (49) which is at the right of the steering wheel.

NOTE

The driver’s seat (12) is equipped with a safety sensor, which allows the machine to be driven by pressing the pedal (2)

only when the operator is on the driver’s seat.

NOTE

The machine is equipped with an anti-skid safety system (display icon (51-J)) that reduces the speed when turning and

when the machine tilts laterally, irrespectively of the pressure on the pedal.

In this case, the reduction of speed is not a malfunction but a characteristic that improves the machine stability and

safety in every condition.

CAUTION!

In case of use of the machine on slopes, drive very carefull and reduce the speed mostly when the ﬂ oor is wet or

slippery.

Always take the ramp perpendicularly to the slope.

To park the machine on slope, reach the parking position and turn off the machine.

Never exceed the gradients indicated on the “Technical Data” paragraph.

Stopping the machine

6. Stop the machine by releasing the drive paddle (2). It is not necessary to lock the machine during stopping or parking, because

the electromagnetic brake on the wheels turn on automatically when the drive pedal is not pressed.

7. Turn off the machine by pressing the push-button (42) and remove the user key (52).

NOTE

The machine is running without the user key (52) in the key reader (41), it automatically switches off after 10 seconds of

complete idle.

NOTE

If the machine is on but not working, it automatically turns off after 5 minutes.

CAUTION!

In the event of an emergency, to stop all machine functions immediately, ﬁ rmly press the push-button (5).

To reset the machine operation, lift the recovery tank assembly (17) and reconnect the battery connector (6).

revised 01/2018

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nilfisk SC2000 Seite 72

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info