Bedienungsanleitung Nilfisk Supreme 150 (Seite 52 von 89) (Dänisch, Schwedisch, Finnisch)

586820

Zoom out

Zoom in

Vorherige Seite

1/89

Nächste Seite

50 Originlal Instructions

All work involving the 240 volt mains electricity

supply must be carried out by a qualiﬁ ed electrical

contractor with full knowledge of the relevant safety

regulations.

The vacuum cleaner will not start

Thermal protector

The vacuum cleaner has a thermal cut-out that trips if the

vacuum cleaner becomes overheated.

Supreme 100 / Supreme 150 / Performer 150 /

Supreme 250 / Performer 250

If this happens - unplug the main power cord to reset the

vacuum cleaner. Wait 5-10 minutes to allow the machine

to cool down. While you are waiting, check the hose, dust

bag and ﬁ lter to be sure that nothing is blocking the ﬂ ow

of air through the machine. The vacuum cleaner should

now start again. If the cut-out trips again, you need to get

a service ﬁ rm to remedy the fault.

Supreme LCD

When the overheat symbol in the display on the cleaner is

activated (models with display) the cleaners’ thermal cut-

out has tripped. For more information regarding thermal cut

out, see Overheat indicator.

Other troubleshootings

• Are you using the correct hose?

Only the original hoses ﬁ t correctly.

• Does the vacuum cleaner start when you try a diﬀ erent

vacuum socket? If so, there is a fault in the electrical

connection to the ﬁ rst socket. Unscrew the socket and

check the connection at the back.

• Is the power supply connected to the vacuum unit?

• Is there power at the socket?

• Is the low-voltage lead connected to the vacuum unit?

• The batteries to the radio remote control (wireless ver-

sion of vacuum cleaner) may have been discharged.

Replace the batteries with new ones, type 1.5V AAA.

The vacuum cleaner will not stop

• Has a metal object become lodged in one of the

vacuum sockets causing the pins to become fused?

Poor suction power

• Are all the vacuum sockets closed properly?

• Has something become jammed in one of the vacuum

sockets?

• Is the container lid closed properly?

• Is the gasket between the container and the lid in

place?

• Is it damaged?

• Is the pipe system blocked?

• Is the dust bag full or clogged?

• Is ﬁ lter clogged?

Supreme LCD Display

The Supreme LCD model has a display giving information

about the machine, Fig. 21.

Speed level

When the start button is pushed or the hose is connected

to the wall socket, the display will turn on and show the

speed level.

10 Troubleshooting Dust bag/bag ﬁ lter indicator

When the dust bag/ﬁ lter symbol starts to ﬂ ash during op-

eration, the cleaner tells you that it is almost time to clean

the bag ﬁ lter and replace the dustbag. When it is time to

do so, symbol will be lit continuously. The dust bag/ﬁ ler

symbol will be lightened after every 20 operation hours

of the cleaner. If the symbol is lit, do like this: Turn oﬀ the

cleaner by the hose handle (remote versions) or remove

the suction hose from the wall inlet or by pushing the on/

oﬀ switch on the display. Then check if the bag ﬁ lter/dust-

bag is clogged. Replacement is described in chapters 7.1,

7.2, 7.3 and 7.4.

In switched oﬀ mode, re-set run time counter by holding

the start/stop button down until the dust bag indicator

goes out (after approx. 5 sec.).

Reduced airﬂ ow indicator - lit

The reduced airﬂ ow symbol on the display indicates that

the airﬂ ow through the vacuum cleaner is reduced. After

30 seconds of operation with reduced airﬂ ow, the vacuum

motor will be shot down in order to prevent damage to the

motor. If the reduced airﬂ ow symbol is lit and the motor

has been shut down, do like this: Check the bag ﬁ lter and

dust bag (see chapters 7.1, 7.2, 7.3 and 7.4) to see if any-

thing is blocking the airﬂ ow. Remove the material causing

the reduced air ﬂ ow symbol to indicate.

Service indicator

When the service symbol starts ﬂ ashing, the motor will

run for one more hour before it stops/will not start. The

purpose of the service symbol is to inform you that it is

time to order service of the cleaner. When the symbol is

continuously lit, the run time counter in the cleaner has

counted that the allowed amount of run time has passed.

You must now contact an authorised service workshop

and let them perform a service of the cleaner and to reset

the run time counter.

Overheat indicator - ﬂ ashing

The overheat symbol indicates that the cleaner has

become overheated. The cleaner stops automatically.

Unplug the main power cored to reset the vacuum cleaner

and wait 5-10 minutes to allow the machine to cool down.

While you are waiting, check the hose, dust bag and ﬁ lter

to be sure that nothing is blocking the ﬂ ow of air through

the machine.

Signal indicator - ﬂ ashing

When the symbol is ﬂ ashing, the hose handle is out of

range and there is no connection to the cleaner. The

cleaner will automatically stop after 30 min. if the hose

handle or the cleaner has not been activated.

WARNING!

Blockages can occur if:

a) the tools and accessories are not used as di rect ed

at all times.

b) wet or damp carpets are vacuumed.

c) foreign objects are vacuumed up when the tools

are not aﬃ xed to the hose.

d) the wall sockets are not kept open until the system

motor stops completly

e) the ﬁ lter and bags are not regularly cleaned and

replaced as per manufacturers in struc tions.

NB! Blockages are caused by misuse and are not

covered by the guarantee or warranty.

Nilfisk Supreme 150 Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nilfisk Supreme 150

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info