Bedienungsanleitung Nilfisk Supreme 150 (Seite 55 von 89) (Dänisch, Schwedisch, Finnisch)

586820

Zoom out

Zoom in

Vorherige Seite

1/89

Nächste Seite

53Original Instructions

12 Wireless communication - Wireless+/Deluxe

Intended use of radio equipment

WARNING!

Do not pull out the suction hose from the cleaner

while the motor/fan unit of the cleaner is running.

These machines have a safety shut oﬀ function.

This shut oﬀ function will be activated when the ma-

chine is operated with a closed vacuum socket.

12.1 Transceiver box

Before you mount the transceiver box to

the wall you should always test if you have

a signal between the transceiver box and

the hose handle in your entire home. Con-

nect the box to the cleaner and turn the

cleaner on and oﬀ using the hose handle

from diﬀ erent places in your home.

The ﬁ rst transmission

The hose handle and the cleaner needs to have a ﬁ rst

communication before starting the cleaner. This is also

valid if the hose handle has been replaced (spare part) or

if you want to connect an extra hose. Do like this before

starting your wireless cleaner:

1) Unplug the main cord.

2) Plug in the cord again, and then push the on/oﬀ button

at the hose handle for approximately 10 seconds. This

must be done within 60 seconds after the cleaner has

been plugged in

3) The handle and the cleaner do now communicate.

Installing the transceiver box

Mount the transceiver box on the wall minimum 1 meter

away from the cleaner for best signal between the trans-

ceiver box and the hose handle. The transceiver box can

be moved to diﬀ erent places in your home for a better

range by using an up to 30 meter network cable. Cables

can often be bought in your local Electronics store.

Connecting the transceiver box

To be able to use the wireless Nilﬁ sk hose handles, you

must ﬁ rst connect the transceiver box to the cleaner. This

is done by using the 2 meter the network cable (RJ45)

that comes with the transceiver box. Connect the cable to

the transceiver box and the right socket in the back of the

cleaner.

12.2 Wireless hose handle

Instruction for use

The on-oﬀ function and power regulation is controlled by

radio technology. You do not have to point at the machine

like infra-red controls. The wireless bent end can be used

anywhere in the house.

Start and stop

Start: One push at the switch will start the cleaner.

Stop: One push at the switch will shut oﬀ the cleaner.

The power regulation can be adjusted in 5 steps. You

switch between the diﬀ erent steps by pressing the (+) or

(-) buttons at the hose handle.

Wireless

The LED-indicator is placed above the on/oﬀ button and

will be activated with diﬀ erent lights depending on the ac-

tions that are taken:

The lamp is activated at start or stop actions or when the

power regulation is adjusted.

The lamp ﬂ ashes a warning light that indicates that the

bag ﬁ lter/dust bag is clogged and needs cleaning/replace-

ment.

You must then check and clean or replace the ﬁ lter/bag.

Deluxe info center display

The display is placed above the on/oﬀ button and will

show diﬀ erent symbols depending of the status of the

cleaner.

Speed level: Bars shows the actual speed level

Low Battery ﬂ ashing: Battery is under 5%, Change bat-

tery.

Service warning / Air ﬂ ow blocked lit: Indicates for both

Service warning and Blocked airﬂ ow. See 10 Trouble-

shooting

Check bag/ﬁ lter ﬂ ashing: It is almost time to change

dust bag and clean ﬁ lter.

Check bag/ﬁ lter lit: Dust bag or ﬁ lter is clogged. Change

dust bag and clean ﬁ lter.

Signal ﬂ ashing: Hose handle is out of range. No connec-

tion to the cleaner.

Overheat ﬂ ashing: Thermal cut-out has tripped and the

cleaner has stopped. See 10 Troubleshooting

Battery

The lifetime of the enclosed batteries in the bent end is ap-

proximately three (3) years. If the battery capacity at opera-

tion start is to low, the cleaner will then be shut oﬀ . If the

cleaner would not start or the power regulation via the hose

handle does not work, you must replace the batteries at the

hose handle. Replace to battery type 1.5V AAA. For more in-

formation and trouble shooting see chapter 10 in this instruc-

tion for use.

How to replace battery at the

hose handle

1) Open the lid of the battery

holder by sliding the lid towards

the front of the hose handle.

2) Replace the used batteries with

two new ones, type 1.5V AAA.

Make sure the polarity of the

batteries is placed correct at the

bracket.

3) Slide the battery lid back until

you hear a click.

On/Oﬀ

Power

regulation +

Power

regulation -

LED-

indicator

Overheat

Signal

strength

Bag/ﬁ lter

Speed

Low battery

Service

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nilfisk Supreme 150 Seite 55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nilfisk Supreme 150

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info