Bedienungsanleitung Nilfisk Supreme LCD (Seite 43 von 89) (Dänisch, Schwedisch, Finnisch)

586824

Zoom out

Zoom in

Vorherige Seite

1/89

Nächste Seite

41Original Instructions

2.1 Fitting the wall bracket

Position the holder so that there is plenty of space above

and below the place where the vacuum unit is to be locat-

ed. Make sure there is a minimum of 500 mm free space

above the container. Mark the positions for the four screw

holes with a pen or similar. Then select appropriate screws

and, if necessary, wall plugs for the type of wall surface to

which the bracket is to be attached. Drill the four holes for

the wall bracket. The diameter of the screw holes in the

holder is 5 mm. Fit the wall bracket with the large opening

pointing upwards, see Fig. 1. Tighten the screws so that

the holder is held ﬁ rmly in place (screws provided).

2.3 Connecting the machine

The machine is connected with the suction pipe in the uppermost position and the

exhaust pipe in the lower position.

This connection should not be glued but can be taped when the unit is serviced at a

later date. The suction pipe socket can be ﬁ tted to two diﬀ erent points depending on

the direction in which you would like to install the pipe system.

To relocate the suction pipe socket, you need to do the following:

1. Release the suction pipe socket by unscrewing the four combination Torx screws

with a Torx T20 or an ordinary screwdriver, Fig. 3.

2. Pull the socket out of the machine, see Fig. 4.

3. Loosen the plug blanking oﬀ the outlet to which you intend moving the suction pipe

socket. Unscrew the four combination Torx screws. Remove the blanking plug from

the machine.

Adapt (move) the suction pipe socket to the new outlet. NB! The socket is marked ”Up”.

Make sure the socket is ﬁ tted with ”Up” uppermost. Fasten the socket by ﬁ tting and

tightening the four screws, Fig. 5.

5. Fit the blanking plug to the outlet previously occupied by the suction pipe socket. Use the four screws to hold it in

place. The exhaust pipe must be ﬁ rmly attached to the wall to ensure its connection with the socket does not loosen.

Remember that you will need to be able to turn the bent pipe in diﬀ erent directions to ensure a suitable pipe layout.

Then connect up the exhaust pipe and muﬄ er, Fig 6. Fit the central vacuum cleaner so that the exhaust pipe is as

short as possible, max. 5 metres. Take the surroundings into consideration when positioning the exhaust. For this

reason, you should always ﬁ t a muﬄ er.

For additional information concerning the assembly and installation of the pipe system and low-current lead, please

refer to the separate assembly instructions supplied with the pipe package.

2 Vacuum unit Supreme 100 assembly instructions

2.2 Locating the vacuum cleaner on the

wall bracket

Position the vacuum unit so that the wall bracket is direct-

ly above the wall bracket, see Fig. 2. Lower the machine

down on to the wall bracket. Make sure the corresponding

bracket on the machine is held ﬁ rmly in place by the wall

bracket.

Fig. 1 Fig. 2

Fig. 3 Fig. 4 Fig. 5

Exhaust

Inlet

Fig. 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nilfisk Supreme LCD Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nilfisk Supreme LCD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info