Bedienungsanleitung Nilfisk UZ 930S (Seite 7 von 32) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

454207

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

INSTRUCTIONS FOR USE

1. To open

a)Pull the retaining clips upward and outward .

b)Lift the cover from the container.

2. Dust bag

Fit the opening on the dust bag over the air inlet. Press the

membrane over the flanged edge on the inlet. Secure with the

lock washer. Use only original dust bags.

3. Hose connection

Push the hose coupling all the way in and turn clockwise.

4. Wand assembly

Standard: Fit the sections together and twist to lock in place.

Telescopic: Push down the catch and then adjust the length.

Max.950mm,min.630mm.

5. Tools

The accessories shown in the pictures may vary from model

to model.

a-b)Combination nozzle

Adjust the nozzle according to the requirements of the floor

you are cleaning. Work with the brush on hard floors and

without it on soft floors.

c)Universal nozzle

for both hard floors and carpets.

d)Crevice nozzle

Use to clean furniture, radiators and others hard-to-reach

places.

e)Small combi-nozzle:

The small combi-nozzle combines a dusting brush for furniture,

picture frames, mouldings etc. with a fold-out nozzle for clea-

ning curtains, furniture and other soft surfaces. The clip on the

hose handle holds the nozzle when it is not in use.

f)Brush nozzle for hard floors.

g)Carpet nozzle with thread pick-up

To use the thread pick-up, turn the nozzle.

6. Suction control

The suction control in the hose handle lets you regulate the

air-flow to prevent the nozzles from fastening to the surfaces

you are vacuum cleaning.

7. Start/Stop

a)Foot-operated on/off switch.

b)On the S2 version a separate switch is provided to

change the motor speed .

c)Plug-in point for powered carpet nozzle. Power is sup-

plied to the socket when the machine is switched on.

8. Warning!

Never attempt to vacuum liquid, glass fragments or ashes!

Wet surfaces can expose the operator to possible electri-

cal shock.

9. Filter

The filters are located inside the lid. To reach them lift out

the filter holder(a). The standard filter(b) and fine filter (c)

should be inspected at regular intervals,e.g. when you

change dust bags, and replace if necessary.Instead of

these two filters you can fit a micro filter of HEPA-quality

(e), wich traps 99,99% of all particles larger than 0,3

microns. The machine is also fitted with a backupp filter (d)

located above rhe motor. This filter should also be inspec-

ted and replaced if necessary.

IMPORTANT!

The UZ 930S/S2 is equipped with a specially

designed cable, which if damaged, must be replaced by a

cable of the same type. These cables are avaible at

authorized service shops and must be installed by trained

personnel.

The UZ 930S/S2 is equipped with a thermal cut-out to

protect the motor and other vital machine parts from

overheating. Should the machine cut out, you will have to

wait at least 5-10 minutes for it to automatically reset.

While you are waiting, switch the machine off and unplug

it, then check the hose, dust bag and filters to be sure that

nothing is blocking the flow of air through the machine.

NB!

Remove the plug from the socket before performing serv-

ice or maintenance.

822 2734 000 Instruction for use UZ 930S S2.p65 9/22/2006, 11:02 AM7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nilfisk UZ 930S Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info