Bedienungsanleitung Nissin MG8000 Extreme - Canon (Seite 6 von 11) (Englisch)

667850

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

19 20

21 22

When setting MG8000 to the slave function, the zoom setting system is

automatically set for the Manual Zoom at 24mm position. The zooming position

can be selected manually to any other position available. In this mode, the

auto-off timer is recommended to set at 60min. or be cancelled (off). The

sensing angle of the slave sensor is 100˚ approx.

In this case, reset this F. Stop on you camera.

As for the traditional type film cameras, no ISO information or F. Stop

information is transferred by the camera. In this case, set ISO value at the

Advanced function page of MG8000.

Press set for 2 seconds, the screen goes to the Advanced Function

page for Av mode.

The flash light is automatically controlled by the photo sensor built-in the flash

unit instead of TTL metering. Select your desired F. Stop on MG8000 and set

this F. Stop on your camera. The intensity of flash light is automatically

controlled for the most proper exposure within the certain area of distance.

Set the camera mode, to or on your camera.

Set the mode on MG8000. From the 6 icons screen,

select M / Av and set .

Select Av and set .

F. Stop is displayed in the screen in accordance with the

ISO setting on the camera.

Select your desired F. Stop and set on the flash

unit.

Press on / off switch to lock the value. (Press it again to

release the lock)

Set the same F. Stop on your camera.

The display screen shows the F. Stop selected, the

camera-subject maximum distance for the proper

exposure and the focal length set on the camera.

The flash light is automatically controlled within the

distance area. The shortest distance for the proper

exposure is approximately 1.0m (3ft.) from the camera to the subject.

The distance varies by changing the focal length and F. Stop set on

MG8000. This Av. mode of MG8000 is not coupled with camera’s aperture

setting. The aperture setting on the flash unit is not controlled by the

camera.

When changing the ISO setting on the camera, the F. Stop of the flash unit

is automatically reset for such corresponding ISO value.

Av. Mode Operation

Set

The mode to be set on the camera:

Advanced custom setting is prepared in this mode.

ADVANCED CUSTOM SETTING

page 14

page 19

page 15

Sub Flash Function

Manual Zoom Setting

Universal Slave Function

Setting of Master and Slave flash:

Setting Master flash:

The master flash to be set is one unit only.

Place the master flash on the camera and switch it on, and set to Manual

function mode or set to the camera’s built-in flash on. Make sure which

mode you chose, digital pre-flash flash system or analogue flash system.

Setting Slave flash MG8000:

Multiple numbers of flashes can be set. Switch MG8000 on and select the

appropriate slave system, either SD or SF.

When flash is set to the slave function, the red

LED starts blinking every 2 seconds showing the

slave function is in order. Make sure the mode

you set, SD or SF which should couple with the

master flash system.

Set slave flash at any place and direct the flash

head as you desire. Slave sensor in the slave

flash is facing to the camera or to the master flash.

Use the included flash stand. Place MG8000 on to the flash

stand which can be placed either on a flat place or on the tripod

by the screw.

NOTE

Metal type accessory shoe is not recommended since it may give electric damage on

the electrical contact of the flash hotshoe.

Advanced custom setting is prepared in this mode.

ADVANCED CUSTOM SETTING

page 14

page 15

Sub Flash Function

Manual Zoom Setting

Universal Slave Function

MG8000 has a universal wireless remote flash system as a slave unit.

You can enjoy creative flash photography with multiple lightings from the

various directions. 2 slave modes are provided in accordance with the flash

system of the master flash.

Slave Digital (SD) for digital pre-flash system and Slave Film (SF) for an

analogue flash system are available.

SD: In this mode MG8000 synchronizes to pre-flash system. The master flash

is to be set at ETTL / ETTL II mode.

SF: In this mode MG8000 synchronizes to the traditional single flash system.

The master flash is to be set at manual mode. Studio strobe lighting system

synchronizes to this mode. This mode also responds to open flash and to

traditional type flash units in the market.

How to find SD or SF?

Select SD on your slave flash and release your camera’s shutter to flash your

master flash. The slave flash flashes if the Master flash is SD, and does not

flash if the Master flash is SF. If your slave flash is set at SF, it flashes against

both of SF and SD flash system.

To set MG8000 to the slave function mode, move cursor

to Slave line at Advanced function page and continuously

select SD or SF in accordance with the system of the

master flash you set.

page 19

Press the set button or wait for 8 seconds to return to

M function screen.

Set

In additional to the Manual power mode, the universal slave function

supports Av operation mode.

Setting Slave flash: Select the slave mode SD or SF and set the

desired F.stop and ISO speed on the Slave flash. As for setting

Master flash, follow to the instruction manual in the Universal slave

page at Manual power operation --- Page 19.

Set

Nissin MG8000 Extreme - Canon Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nissin MG8000 Extreme - Canon

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info