Bedienungsanleitung Nissin MG8000 Extreme - Nikon (Seite 6 von 11) (Englisch)

667851

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

19 20

21 22

When setting MG8000 to the slave function, the zoom setting system is

automatically set for the Manual Zoom at 24mm position. The zooming position

can be selected manually to any other position available. In this mode, the

auto-off timer is recommended to set at 60min. or be cancelled (off). The

sensing angle of the slave sensor is 100˚ approx.

In this case, reset this F. Stop on you camera.

As for the traditional type film cameras, no ISO information or F. Stop

information is transferred by the camera. In this case, set ISO value at the

Advanced function page of MG8000.

Press set for 2 seconds, the screen goes to the Advanced Function

page for Av mode.

The flash light is automatically controlled by the photo sensor built-in the flash

unit instead of TTL metering. Select your desired F. Stop on MG8000 and set

this F. Stop on your camera. The intensity of flash light is automatically

controlled for the most proper exposure within the certain area of distance.

Set the camera mode, to or on your camera.

Set the mode on MG8000. From the 6 icons screen,

select M / Av and set .

Select Av and set .

F. Stop is displayed in the screen in accordance with the

ISO setting on the camera.

Select your desired F. Stop and set on the flash

unit.

Press on / off switch to lock the value. (Press it again to

release the lock)

Set the same F. Stop on your camera.

The display screen shows the F. Stop selected, the

camera-subject maximum distance for the proper

exposure and the focal length set on the camera.

The flash light is automatically controlled within the

distance area. The shortest distance for the proper

exposure is approximately 1.0m (3ft.) from the camera to the subject.

The distance varies by changing the focal length and F. Stop set on

MG8000. This Av. mode of MG8000 is not coupled with camera’s aperture

setting. The aperture setting on the flash unit is not controlled by the

camera.

When changing the ISO setting on the camera, the F. Stop of the flash unit

is automatically reset for such corresponding ISO value.

Av. Mode Operation

Set

The mode to be set on the camera:

Advanced custom setting is prepared in this mode.

ADVANCED CUSTOM SETTING

page 14

page 18

page 15

Sub Flash Function

Manual Zoom Setting

Universal Slave Function

Setting of Master and Slave flash:

Setting Master flash:

The master flash to be set is one unit only.

Place the master flash on the camera and switch it on, and set to Manual

function mode or set to the camera’s built-in flash on. Make sure which

mode you chose, digital pre-flash flash system or analogue flash system.

Setting Slave flash MG8000:

Multiple numbers of flashes can be set. Switch MG8000 on and select the

appropriate slave system, either SD or SF.

When flash is set to the slave function, the red

LED starts blinking every 2 seconds showing the

slave function is in order. Make sure the mode

you set, SD or SF which should couple with the

master flash system.

Set slave flash at any place and direct the flash

head as you desire. Slave sensor in the slave

flash is facing to the camera or to the master flash.

Use the included flash stand. Place MG8000 on to the flash

stand which can be placed either on a flat place or on the tripod

by the screw.

NOTE

Metal type accessory shoe is not recommended since it may give electric damage on

the electrical contact of the flash hotshoe.

In additional to the Manual power mode, the universal slave function

supports Av operation mode.

Setting Slave flash: Select the slave mode SD or SF and set the

desired F.stop and ISO speed on the Slave flash. As for setting

Master flash, follow to the instruction manual in the Universal slave

page at Manual power operation --- Page 18.

Repeating the flash illumination on the subject freezes the sequence of motion

in one frame of picture.

In this mode, the power level, frequency and the number of flashes are to be

set on the flash unit in advance.

Power Ratio:

　Uncontrolled manual power is provided in 5 steps, from 1/8 to 1/128 power.

Frequency :

　1 Hz to 90 Hz frequency can be set.

Flash Times :

　1 time to 90 times can be set.

Set the camera mode to M on your camera.

Set the shutter speed on your camera in accordance with the guide table in

the next page.

Set the mode on MG8000. From the 6 icons screen, select 　

　 and set .

Value setting screen will appear with the default values

preset as shown.

In this mode, the reflector zooming function is

automatically set for option. Either Auto zoom or Manual

zoom setting is selectable.

Select the function and choose the desired value

one by one.

Press on / off switch to lock this condition.

Or press set or wait for 8 seconds to return the 6 icons

screen.

The use of tripod is recommended for this flash mode.

Multiple Flash Mode (Repeat flash/Stroboscopic flash)

Set

The mode to be set on the camera:

Set

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nissin MG8000 Extreme - Nikon Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nissin MG8000 Extreme - Nikon

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info