cleaning agent, clear, cold water only! For reasons of hygiene we recommend the removal and clean-
ing of the unit thoroughly after each run of the cleaning programme (see 5.4.).
Open the service door on the right of the casing (g. 1/L) by pulling the inner handle slightly
towards you and carefully move the service door away from casing.
Remove the brew unit by pressing the red switch upward and turning the handle all the way to
the left until it snaps into place (g. 12).
Carefully remove the brew unit using the handle.
Clean the brew unit under running water and let it dry.
Reinsert the brew unit carefully and lock it by pressing down the red switch and turning the handle.
Close the service door and in doing so carefully place the pivots at the back of the door into the
notches. Make sure that the door (g. 1/L) completely snaps back into place.
5.8. Changing the lter
The lter will need to be changed after about 50 l of water have been drawn. The display shows
“CHANGE FILTER”.
You can still make coffee, but we recommend changing the lter immediately.
Turn the right rotary control to “SETTINGS” and press it.
Turn the right rotary control to “FILTER” and press it.
Turn the right rotary control to “INSERT FILTER? YES”, so the appliance recognizes the new lter.
Empty the water tank (g. 1/F and 2) and unscrew the lter carefully, using the integrated tool at
the end of the measuring spoon (g. 4).
Discard the lter.
Press the right rotary control.
The display shows “INSERT FILTER” or “FILTER INSERTED” in case the lter has already been
replaced.
Screw the new lter into the dedicated slot in the water tank, using the integrated tool at the end
of the measuring spoon (g. 4).
Attention: Do not overtighten or bend the lter.
Fill the tank with fresh water and insert it back into the appliance.
Place a sufciently large bowl (at least 0.5 l) underneath the spout (g. 1/E) and press the right
rotary control.
The system is being rinsed. The display shows “FILTER RINSES”.
Wait a short while until no more water is dispersed from the spout.
The system reheats. The appliance is ready for use again. The display shows the main menu.
Attention: The lter needs changing after a maximum of two months if the appliance is not in regular use.
The display will show no status message. Use the dial (by the month) at the top of the lter to select the
date of change.
5.9. Maintenance status
The appliance will indicate if cleaning or descaling are imminent.
Turn the right rotary control to “MAINTENANCE” and press it.
Turn the right rotary control to “MAINTENANCE STATUS” and press it.
The display shows:
“CLEANING SYSTEM”
“CLEANING LATER”
“DESCALING”
“CHANGE FILTER”
The respective bar will show you if cleaning or descaling are imminent. The further to the right it
progresses, the sooner one or both need to be done.
Press the right rotary control to exit “MAINTENANCE STATUS”.
Attention: Please clean and descale regularly, at the latest when the display asks you to! Otherwise your
warranty could be compromised.
6. System reports
Report Cause Solution
Fill system Rell pipe system Press right rotary control
Filter possibly defect Remove or replace lter
Fill water Water tank is empty Fill water tank
Water tank not inserted or
inserted incorrectly
Insert water tank correctly
(see 2.3.)
Fill beans No beans Fill beans
(see 2.3.)
Beans stuck in container Stir beans with a spoon
Clean bean container with
a cloth
Note: The display ”FILL BEANS” will only go off after the next coffee request!
Empty trays Drip tray and/or used coffee
container are full
Empty drip tray and/or used
coffee container
No trays No drip tray with used
coffee container or incorrectly
inserted
Insert drip tray with used
coffee container
Cleaning necessary System cleaning necessary Clean system
(see 5.4.)
Descaling necessary System descaling necessary Descale system
(see 5.5.)
Change lter Filter exhausted Change lter
(see 5.8.)
Brew unit removed Brew unit tted incorrectly Fit brew unit correctly and
snap into place
(see 5.7.)
86 87
5. Cleaning and maintenance 6. System reports
