Bedienungsanleitung Nivona NICR821 (Seite 6 von 16) (Englisch)

774459

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Followed by “PLEASE Flush”.

➔Press the rotary control.

The display shows “SYSTEM FLUSHES”.

Once the system has reached operating temperature, the main menu will appear in the display to

show that the appliance is ready for use.

The rst cup: When you prepare your rst cup of coffee the grinder will be empty. It is possible that

after the initial grinding the display will show “REFILL BEANS” and no coffee is produced.

➔In case that happens, please follow the display’s instruction and press the rotary control again.

The process will then be repeated.

Note: If you are using a lter and programmed the system to “FILTER INSERTED? YES”, the internal

water softening is automatically set to water hardness level 1! The appliance needs descaling less

frequently – but always descale when asked to do so and always with FILTER REMOVED. The lter will

be at after approx. 50 l of water have been drawn (changing lter see chapter 3.1).

Attention: Even if the display does not indicate “PLEASE CHANGE FILTER“, the lter needs changing after

a maximum of two months if the appliance is not used regularly (see chapter 5.8.).

2.4.2. Using the appliance without lter

If you prefer to use the appliance without lter, the lter setting “FILTER INSERTED? NO” needs

to be set. This is important because depending on the water hardness the appliance needs to be

descaled more often (ex-factory the appliance comes with the setting “FILTER INSERTED? NO”!).

➔Turn the rotary control to “FILTER INSERTED? NO”.

➔Press rotary control to conrm.

The display shows the level of water hardness.

Note: For production reasons the internal pipes may be empty when setting the appliance up for the

rst time. The appliance will show this as follows: on the display it says „PLEASE FILL”, once the appli-

ance has been switched on with the On/Off switch (g. 1/H).

➔Place a sufciently large bowl (minimum contents 0.5 l) under the spout.

➔Press rotary control.

The system is being lled with water which may emerge from the spout (g. 1/E).

Once the system has reached production temperature, the display shows “PLEASE RINSE”.

➔Press rotary control.

The system is now being lled with water.

2.4.3. Adjusting the water hardness

Depending on the water hardness in your area, the appliance needs to be descaled every now and

again. For the system to be able to indicate that this is necessary, you need to set the correct water

hardness prior to rst use.

Level 3 is the ex-factory pre-set level.

First test the water quality with the enclosed test strip:

➔Dip the test strip into the water and shake it lightly.

➔After about one minute you will be able to read the result by counting the red dots on the test strip.

➔The different levels are listed as follows and can be adjusted:

Test strip / Degree of hardness = Display

1 red dot / 1–7° = LEVEL 1

2 red dots / 8–14° = LEVEL 2

3 red dots / 15–21° = LEVEL 3

4 red dots / >21° = LEVEL 4

Tip: If the test strip does not show any red dots, please set up level 1.

How to set up the water hardness:

➔Turn the rotary control onto the correct degree of hardness.

➔Press the rotary control to conrm.

The display shows “NIVONA”.

The display shows “PLEASE RINSE”.

➔Press the rotary control. The display shows “SYSTEM IS CLEANING”.

The system is now being lled with water and heated up.

Once the appliance is ready for use the main menu is shown on the display.

The rst cup: When you prepare your rst cup of coffee the grinder will be empty. It is possible that

after the initial grinding the display will show “REFILL BEANS”, and no coffee is produced.

➔Follow the display and press the rotary control again.

The process will then be repeated.

2.5. Switching the appliance on during operation

When you have started the appliance for the rst time (g. 2.4), proceed as follows for all other start-ups:

➔Switch the appliance on using the on/off switch (g. 1/H).

The display shows “NIVONA, SYSTEM IS HEATING UP”.

Once production temperature has been reached, the display shows “PLEASE RINSE”.

➔Press the rotary control.

The system is now being rinsed. Afterwards the appliance is operational. The display shows the main

menu (g. 1/A).

Tip: If you do not use the appliance for a prolonged period of time (e.g. holidays), switch it off using

the on/off switch (g. 1/J) and pull the mains plug.

Tip: The machine has a pre-programmed setting ex-factory for each coffee variety. This means that

you can brew your rst coffee straightaway (see chapter 4.). However, we do recommend making the

necessary adjustments according to your preferences before you do so (see chapter 3.)

2.6. Pre-heating cups (model 859)

Your appliance comes with a function for pre-heating cups.

➔Pressing the button (g.1/K) activates the cup heating. To do this the on/off switch needs to be

switched on (g. 1/H).

The display shows “CUP HEATING ON”.

➔By pressing the button again (g. 1/K) the cup heater is switched off.

The display shows “CUP HEATING OFF”.

Tip: Pre-heat the cups according to your personal preference to optimize aroma and temperature.

Note: If AUTO ON is switched on and you want the cup heating to start automatically, please also set

the cup heating on AUTO ON (see 3.6.).

2.7. ECO mode

If neither rotary control nor any button is used for a longer period of time, the appliance automati-

cally switches into ECO mode. The display shows “SAVING ENERGY”.

➔By using the rotary control or any button, the appliance switches back into standard mode.

The display shows the main menu.

70 71

 

2. Initial start-up 2. Initial start-up

Nivona NICR821 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nivona NICR821

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info