Bedienungsanleitung Nokia 9000i (Seite 27 von 126) (Englisch)

297910

Zoom out

Zoom in

Vorherige Seite

1/126

Nächste Seite

Chapter 3 - Contacts 3-3

(number 1 is reserved for calling your voice mail-

box, see chapter 4 "Telephone: Telephone set-

tings" on page 4-6). For information on how to use

the speed dials, see chapter 13 "Phone interface:

Using memory - Dialling shortcuts" on page 13-5.

To set speed dials:

1 Press Speed dials in an opened contact card.

All phone number fields of the contact card

are shown.

2 Select a field to which you want to assign a

speed dial and press Change. Select a loca-

tion and press OK.

To change or remove speed dials:

1 Select the speed dial you want to change or

remove and press Change.

2 Move the selection frame to the location you

want to use and press OK. If you want to re-

move a speed dial location, choose None.

Storing DTMF tones

The Dual Tone Multi Frequency (DTMF) tones al-

low you to communicate with voice mailboxes,

computerised telephony systems, etc. For infor-

mation on how to send DTMF tones, see chapter

4 "Telephone: Managing calls - Sending DTMF

tones" on page 4-5, or chapter 13 "Phone inter-

face: Sending DTMF tones" on page 13-3.

• If you only communicate with the contact

using DTMF tones, create a contact card for

the DTMF contact.

• If you need both a voice and a DTMF phone

number for the contact, add a new field to an

existing contact card. The DTMF sequence can

be stored either in the Tel field, after the tele-

phone number, or separately, in a DTMF field.

If you store the sequence in a Tel field, the

phone number and the DTMF sequence must

be separated by one of the DTMF special char-

acters. Label the field (with Change label) so

you can identify the DTMF sequence.

The DTMF special characters are listed in the

following table:

Logs

The Contacts application shows all communica-

tion events as two logs:

• General log shows all (or certain types of)

communication events in chronological order,

see figure 3-2.

• Individual log shows a list of all communi-

cation events relating to the selected contact.

To access the logs:

1 Press Logs in the Contacts main view. The

command set changes.

2 Select the desired log type by pressing either

Individual log or General log.

To erase the contents of the log:

1 Press Clear list. A pop-up box opens to let you

define which contacts will be deleted (meas-

ured in days). The clearing procedure reflects

on the other log, as well.

To create a new contact card:

1 Open the General log.

Character Function

* and #

May be used if the DTMF

service requires them.

p (pause)

Inserts a pause of 2.5 sec-

onds in front of, or between,

DTMF digits.

w (wait)

When the “w” character is

stored in a sequence, the

rest of the sequence is not

sent until you press Send

again in the Telephone

application.

Table 3-1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nokia 9000i Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nokia 9000i

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info