Bedienungsanleitung Nokia 9000i (Seite 100 von 126) (Englisch)

297910

100

Zoom out

Zoom in

Vorherige Seite

1/126

Nächste Seite

13-4 Using memory

Automatic transmission

In order to send DTMF tones automatically, you

must store them first. Storing DTMF strings is

most conveniently done in the communicator in-

terface, see chapter 3 "Contacts: Contact cards -

Storing DTMF tones" on page 3-3. If you want to

store DTMF strings in the phone interface, see

"Using memory: Storing information via the

phone interface" on page 13-5.

1 Press Memory. Key in the name of the con-

tact card that contains the DTMF service

phone number and the DTMF digits and press

Find.

For how to recall information, see "Using

memory: Recalling information" on page 13-5.

Note: When stored DTMF tones are recalled in

the phone interface, only DTMF strings

that have been stored in a Tel field can be

used.

2 When the recalled string (containing the

phone number and the DTMF digits) is on the

display, press .

After the connection has been established,

the DTMF tones will be sent directly, after a

small pause (if the sequence contained the p

character) or after you press for the sec-

ond time (if the sequence contained the w

character).

Using memory

The phone numbers and names you store are nor-

mally located in the standard memory of the

communicator, indicated by the letter “B” on the

phone interface display.

The “B” memory is the communicator memory,

known as the Contacts directory. When the com-

municator is started up for the first time, the “B”

memory is selected automatically.

The “A” memory is located on the SIM card that

is inserted in the communicator. The SIM card

memory uses numbered memory locations to

store data. When numbers are saved in the SIM

card (“A”) memory, a message will indicate its lo-

cation number. The number of standard memory

locations available on SIM cards varies from one

card to another.

When the “A” memory is selected, the phone in-

terface stores all contact information on the SIM

card and cannot access the Contacts directory.

Therefore, the use of the communications appli-

cations of the communicator interface will be

less convenient (you will have to enter most con-

tact information manually). This manual will as-

sume that you use the standard “B” memory.

Keying in a name

1 Press the Memory selection key to switch to

the alpha mode (the indicator is shown

on the phone interface display).

2 Press the key that has the desired character.

If the character you want is not the first to be

displayed, press the key again within one sec-

ond (before the cursor appears) to display the

next character. Keep pressing the key until

the desired character appears.

3 If you miss a character, keep pressing the key

until it appears again; or first press and

then start pressing the key again.

If you want a lower case character, press and

hold a key until the character appears in low-

er case. All further letters will appear in lower

case until a key is pressed and held once

again.

To enter a space between characters, press .

To correct a mistake, press .

ABC

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nokia 9000i Seite 100

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nokia 9000i

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info