Bedienungsanleitung Nokta Makro Gold Finder 2000 (Seite 2 von 2) (Englisch)

801558

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Assembly

(2) To join the middle rod with the

upper and lower rods, open the

lever latches and engage the

pieces together. After adjusting

the length of the device to your

height, press the latches to

secure.

(1) After inserting the washers on

the lower shaft, place the lower

shaft in its location on the search

coil. Secure by tightening the

screw and nut. Do not

overtighten.

(3) Wind the search coil cable on

the shaft without stretching too

much. Then, plug the connector to

the search coil input socket on the

system box and secure by

tightening the nut. While

tightening, you may hear clicks

indicating that the connector is

secured.

(4) To adjust the armrest to your

comfort, push the red lock forward.

Adjust it by sliding it up or down

and secure by pushing the red lock

in the opposite direction. Insert the

armrest strap as shown in the

picture and adjust it to your arm

size and tighten.

Warning Icons

Low Battery Warning

Battery icon on the display shows the battery life status. When the

charge decreases, the bars inside the battery icon decrease, too.

When the battery is depleted, the battery icon will start flashing.

Check Coil

It indicates an interruption in the search coil transmitter signal. The

search coil connector may be unattached, loose or disconnected or the

search coil may have a defect. If the issue continues when you change

the search coil, there may be an issue in the coil control circuit.

Overload

Shallow and/or large targets may cause an overload and the device

starts to generate a continuous sound which resembles a siren.

Overload icon is shown on the display simultaneously. In such a

case, lift the search coil up until the icon disappears.

Software Update

Gold Finder 2000 has software update capability. All software updates made

after the device is released to the market will be announced on the product's

web page along with updating instructions.

WARRANTY

This product has a 2 year limited warranty from the time of purchase. Please

refer to www.noktadetectors.com for further warranty information.

Factory Defaults

Press and hold the M button immediately after turning on the device.

When the display light turns on, release the M button. The bar will rise and fall,

the battery icon will fill up and the device will revert back to factory defaults.

Changing the Wireless Connection Channel

To change the channel, press and hold the M button for 3 seconds while

the device is on. The frame around the search modes icon will start blinking.

Change the frequency using the volume +/- buttons.

The channel number will be reflected on the right side of the bar. The right

side of the bar will start filling up / falling each time you press the sensitivity

+/- buttons. There are a total of 20 channels. When the bar is completely

empty, it means that the wireless connection is off.

Wireless Connection

Gold Finder 2000 has a built-in wireless module which allows for wireless

speaker and wireless headphones connection. The wireless speaker is

supplied with the device and the pairing instructions are provided below. You

can find the pairing instructions for the wireless headphones in the Nokta

Makro 2.4GHz Wireless Headphones sold separately.

Turn on the wireless speaker by pressing and holding down the power button

and do not let go of the button until the beep indicating the battery status is

heard. The green LED on the speaker will start flashing fast. The speaker is

ready to be paired with the device. Turn on the device while pressing the

sensitivity plus (+) button. Do not let go of the sensitivity plus (+) button until

the device is turned on and the wireless icon appears at the center

bottom of the screen. Once the wireless icon is displayed, the sound will be

heard both from the device and the speaker.

If the pairing is not successful, repeat the above steps.

FCC STATEMENT

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may

cause undesired operation.

For Consumers within the European Union: Do not dispose of this

equipment in general household waste. The crossed wheeled bin

symbol on this equipment indicates this unit should not be

disposed of in general household waste, but recycled in compliance

with local government regulations and environmental requirements.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nokta Makro Gold Finder 2000 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nokta Makro Gold Finder 2000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info