Bedienungsanleitung Nokta PulseDive 2-in-1 Set (Seite 9 von 12) (Englisch)

801561

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

During the operation of the PulseDive, the Green LED blinks once when you

press any button. It lights up solid when the buttons are pressed down and

held.

POWER ON-OFF

Press the on-off button once to turn the device on. A beep will be heard and

the LEDs will light up according to the battery life status. To turn the device

off, press and hold the on-off button. Double beeps will be heard, regardless

of the mode used, and both LEDs will light up simultaneously.

The device automatically retunes itself when it is turned on. Therefore, keep the

device away from metal objects while powering it on. If you are going to use the

device on wet beach sand or on highly mineralized ground, it is recommended to

turn the device on by placing the search coil on the ground or to turn the device

and retune it over the ground. Although this results in a slight loss of depth, it

provides a more stable operation.

You can also retune your device instantly when the device emits false signals.

In order to retune the device, press the on-off button once. Do not retune the

device over metal objects. Otherwise, the device will experience loss of depth.

When the device is turned off and on, it will start with the last saved settings.

DETECTION MODES

The device has 3 detection modes: Audio, vibration, audio and vibration.

Press the (F) button to change the mode.

Red LED

In addition to the above detection modes, PulseDive also has a red LED that

indicates metal detection.

When the red LED is activated, it flashes once upon metal detection regardless

of the mode used. As you get closer to the target, it flashes faster and more

frequently.

To turn on / off the red LED, press and hold the adjustment button (A).

SENSITIVITY

There are 5 levels of sensitivity. To adjust the sensitivity, press the adjustment

button (A) while holding the function button (F) pressed down. Each time you

press the A button, the sensitivity increases 1 level. Each level is indicated by a

number of beeps and/or vibrations depending on the mode used. For example

level 4 is indicated by 4 beeps and/or vibrations. At maximum sensitivity -level

5- the device emits a long beep and/or vibration. If the red LED is active, it lights

up solid.

Inside highly mineralized holes, the device may produce false signals. In such a

case, reduce the sensitivity.

LED FLASHLIGHT

To activate flashlight, press the adjustment button (A) once while the device is

on. Press it again to turn off.

DIVE MODE

If you are diving with the PulseDive, you need to switch the device to dive

mode in order to prevent the buttons from being pressed by water pressure.

While in the dive mode, the buttons are locked and do not work. Therefore,

make sure that the device is set to the desired settings before switching to

dive mode. Recommended settings are vibration and the red LED to be on.

Hold the device upside down (LEDs facing down) as shown in the picture and

press the (A) and (F) button simultaneously. The green LED will light up and a

beep will be heard and/or the device will vibrate depending on the mode used.

If the red LED is on, it will also blink once.

In dive mode, the device will not detect any targets while you hold it upside

down. It will detect targets when you flip and hold it the right way.

Repeat the steps above to exit the dive mode. When exiting the dive mode, only

a beep will be heard and/or the device will vibrate depending on the mode used;

the green LED will not light up. If the red LED is on, it will also blink once.

IMPORTANT! The PulseDive will not switch to dive mode while detecting metal!

NOTE: The wireless headphones will not work if the device is switched to dive

mode while it is connected the wireless headphones. The wireless headphones

will connect automatically once the device exits the dive mode.

OPERATION OF THE DEVICE

IMPORTANT! The PulseDive comes with 2 battery compartment covers. While

using the device in dive mode, use the battery compartment cover that comes

attached to the device and while using the device on land, use the one that

is designed for land use to obtain a louder volume. The cover for land use is

waterproof and can be washed. However, it cannot be used for diving. To prevent

the filter, which is used on the cover for land use, from any damage, do not

insert any sharp objects into the holes for cleaning or any other purposes.

LOST ALARM

The PulseDive has a lost alarm feature which makes it easier to find the device

in case you lose it. If no button is pressed and/or if the device does not detect

any targets for 5 minutes, the lost alarm is activated. The device starts emitting

beeps at short intervals and the LED flashlight starts flashing.

When the lost alarm gets activated while the device is connected to the

wireless headphones, the audio is heard through the device and not through

the headphones anymore.

FREQUENCY SHIFT

It is used to prevent the device from interfering with other detectors nearby.

To shift the frequency, press the on-off button while holding the (F) button

pressed down. Each time you press the on-off button, a beep will be heard

and/or the device will vibrate and the frequency will shift 1 step. There are 40

steps in frequency shift. The central frequency, which is the factory default,

is indicated by double beeps / vibrations.

WIRELESS HEADPHONES CONNECTION

PulseDive has an internal wireless connection module for wireless headphones use.

To activate the wireless connection, turn the device on while holding the (F)

button pressed. The green LED will start flashing at certain intervals to indicate

that the wireless module is on.

To turn the wireless connection off, power off the device while holding the (F)

button pressed.

The pairing instructions can be found in the Nokta 2.4GHz Wireless Headphones

which are sold separately.

IMPORTANT! If the wireless connection is on but the device is not connected to

the wireless headphones, the device will do a channel search and the the green

LED will light up for almost 5 seconds at start up. During this period, the device

will NOT detect metal!

Nokta PulseDive 2-in-1 Set Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nokta PulseDive 2-in-1 Set

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info