Bedienungsanleitung La Nordica CARILLON 16-9 (Seite 19 von 60) (Deutsch, Englisch, Holländisch, Französisch)

542375

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

CARILLON 4:3 – CARILLON 16:9 – CARILLON CLASSIC

7196755 Rev.09 – EN 19

• observe the technical data of the instructions manual; Should the flues have a square or rectangular section,

internal edges must be rounded with a radius not lower than 20 mm. For the rectangular section, the maximum

ratio between the sides must be ≤ 1.5.

A too small section causes a decrease of the draught. It is suggested a minimum height of 4 m. The following features

are forbidden and therefore they endanger the good operation of the device:

asbestos cement, galvanized steel, rough and porous internal surfaces. Picture 4 gives some examples of execution.

The minimum section must be 4 dm

(for example 20 x 20 cm) for devices whose duct diameter is lower than

200 mm or 6.25 dm

(for example 25 x 25 cm) for devices with diameter greater than 200 mm.

The draught created by the flue must be sufficient, but not excessive.

A too big flue section can feature a too big volume to be heated and consequently cause difficulties in the operation of

the device; to avoid this, tube the flue along its whole height. A too small section causes a decrease of the draught.

The flue must be properly spaced from any flammable materials or fuels through a proper insulation or an air

cavity. It is forbidden to let plant piping or air feeding channels pass in the same flue. Moreover, it is forbidden to

create movable or fixed openings on the same for the connection of further other devices.

6. CONNECTION TO THE CHIMNEY

For safety reasons the door of the appliances with constructive system 1, must be opened only for the loading of the

fuel or for removing the ashes, while during the operation and the rest, the door of the hearth must remain closed.

The appliances with constructive system 2 must be connected to their own flue. The operating with open door is

allowed under supervision. The connection pipe to the flue must be the shortest possible, right, tight and according to

the current regulations.

The connection to the chimney must be performed with stable and strong pipes (we recommend a thickness of 2

mm). The pipe for smokes exhaust must be fixed hermetically to the chimney. The diameter inside the connection

pipe must correspond to the external diameter of the smokes exhaust small trunk of the stove. This is ensured by

pipes according to DIN 1298.

ATTENTION: Eventual flammable pieces in the area of 20 cm round the connection pipes must be changed with

fireproof and not sensitive to heat materials.

For a good operation of the equipment it is essential that in the installation place it is introduced sufficient air for

combustion (see CHAPT. 10).

The depression on the chimney should be 12 - 14 Pa (=1.2-1.4 mm of water column). The measurement must be

done always with the equipment hot (rating calorific value). When the depression exceeds 17 PA (1.7mm of water

column) it is necessary to reduce the same with the installation of an additional flue adjuster (butterfly valve) on the

exhaust pipe or in the chimney.

For safety reasons the door of the stove must be opened

only for the loading of the fuel or for removing the ashes,

while during the operation and the rest, the door of the hearth must remain closed.

During its operation we suggest you slowly rotate the stove CARILLON. The rosette of the flue must be fixed

with nails or screws and the junction pipe must be fixed with a 90°bend, in order to avoid during the rotation

of the stove the detachment of the smoke pipe and a consequent danger of fire.

6.1. CHIMNEY CAP POSITION

The draught of the flue depends also on the suitability of the chimney cap.

The

refore, if it is handicraft constructed, the output section must be more than twice as big as the internal section of

the flue. Should it be necessary to exceed the ridge of the roof, the chimney cap must assure the discharge also in

case of windy weather (Picture 5).

The chimney cap must meet the following requirements:

• have internal section equivalent to that of the stack.

• have a useful output section twice as big as the flue internal one.

• be manufactured in such a way as to prevent the penetration of rain, snow, and any other foreign body in the

flue.

• be easily checkable, for any possible maintenance and cleaning operation.

Picture 5

(1) Industrial chimney cap

with pre-fabricated elements

– it allows an excellent

discharge of the smokes.

(2) Handicraft chimney cap.

The right output section must

be at least twice as big as the

internal section of the flue

(ideal value: 2.5 times).

(3) Chimney cap for steel

flue with internal cone

deflector of smokes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

La Nordica CARILLON 16-9 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info