Bedienungsanleitung La Nordica LUCY (Seite 22 von 56) (Deutsch, Englisch, Französisch, Italienisch)

542372

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

FIAMMETTA BII – GIORGIA BII – ASIA BII – FIORELLA BII – LUCY BII

22 7196601 – EN

variety Kg/mc KWh/Kg moistness 20%

Beech 750 4,0

Oak 900 4,2

Elm 640 4,1

Poplar 470 4,1

Larch* 660 4,4

Spruce* 450 4,5

Scots pine *

550 4,4

* RESINOUS WOOD NOT SUITABLE FOR THE BURNING

ATTENTION: the continuous and protracted use of aromatic wood (eucalyptus, myrtle etc.) quickly damages the cast

iron parts (cleavage) of the product.

9. LIGHTING

IMPORTANT: T

he first time that the appliance is lit, there will be an odour given off (due to the drying of the

adhesives of the junction chord), which disappears after a short use. It must be ensured, in any case, a good

ventilation of the environment. Upon the first ignition we suggest loading a reduced quantity of fuel and slightly

increasing the calorific value of the equipment.

To perform a correct first lighting of the products treated with paints for high temperature, it is necessary to

know the following information:

• the construction materials of the involved products are not homogeneous, as matter of fact there are

simultaneously parts in cast iron, steel, refractory material and majolica;

• the temperature to which the body of the product is subject is not homogeneous: from area to area, variable

temperatures within the range of 300°C - 500 °C are detected;

• during its life, the product is subject to alternated lighting and extinguishing cycles in the same day, as well as to

cycles of intense use or of absolute standstill when season changes;

• the new appliance, before being considered seasoned has to be subject to many start cycles to allow all

materials and paints to complete the various elastic stresses;

• in detail, initially it is possible to remark the emission of smells typical of metals subject to great thermal stress,

as well as of wet paint. This paint, although during the manufacture it is backed at 250 °C for some hours, must

exceed many times and for a given period of time the temperature of 350 °C before becoming completely

embedded in the metallic surfaces.

Therefore, it is extremely relevant to take these easy steps during the lighting:

1) Make sure that a strong air change is assured in the room where the appliance is installed.

2) During the first starts, do not load excessively the combustion chamber (about half the quantity indicated in the

instructions manual) and keep the product continuously ON for at least 6-10 hours with the registers less open

than the value indicated in the instructions manual.

3) Repeat this operation for at least 4-5 or more times, according to your possibilities.

4) Then load more and more fuel (following in any case the provisions contained in the installation booklet

concerning maximum load) and, if possible, keep the lighting periods long avoiding, at least in this initial phase,

short ON/OFF cycles.

5) During the first starts, no object should be leaned on the appliance and in detail on enamelled surfaces.

Enamelled surfaces must not be touched during heating.

6) Once the «break-in» has been completed, it is possible to use the product as the motor of a car, avoiding abrupt

heating with excessive loads.

To light the fire, it is suggested using small wood pieces together with paper or other traded lighting means. It is

FORBIDDEN to use any liquid substance as for ex. alcohol, gasoline, oil and similar.

The openings for air (primary and secondary) must be opened together just a little (you must open the eventual

butterfly valve placed on the pipe of smokes exhaust). When the wood starts burning, adjust the air for combustion

according to the instructions on paragraph 10.

Never overload the stove (compare the technical table - max. quantity of loadable fuel).

Too much fuel and too much air for the combustion may cause overheating and then damage the stove.

The warranty does not cover the damages due to overheating of the equipment.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

La Nordica LUCY Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info