Bedienungsanleitung Nordland WD 8126 EL (Seite 16 von 36) (Englisch)

69783

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

pour it into the main wash compartment

and, if you wish to carry out a programme with

the prewash phase, pour it into the

compartment marked .

If required, pour fabric softener into the

compartment marked (the amount used

must not exceed the «MAX» mark in the

drawer). Close the drawer gently.

Select the required programme by means of

the programme selector dial (1)

Turn the programme selector dial to the

required programme. The green light of button

8 starts blinking.

It can be turned either clockwise or

anticlockwise. On position «O» the programme

is reset and the machine is switched OFF.

At the end of the programme the selector

dial must be turned to position «O», to

switch the machine off.

IMPORTANT!

If you turn the programme selector dial to

another programme when the machine is

working, the red light will of the button

8 blinks

3 times and the message Err is displayed on

the display to indicate a wrong selection. The

machine will not perform the new selected

programme.

Select the spin speed or the Rinse Hold

option by pressing button

The relevant light will light up.

When selecting a programme, the light

corresponding to the maximum speed allowed

for that programme will illuminate (refer to the

section «Programme table» for the maximum

allowed spin speed).

Select the desired option by means of

buttons

5 and 6

Depending on the programme, different

functions can be combined. These must be

selected after choosing the desired programme

and before depressing the button 8. The

corrisponding light illuminates.

For more information about the compatibility of

the options with the washing programmes,

refer to the section «Programme table».

Select the delayed start by pressing the

button

Press this button to select the required delay.

The selected delay time value will appear on

the display for few seconds, then the duration

of the programme will appear again.

You must select this option after you have set

the programme and before you press the

button

You can cancel the delay time at any moment,

before you press button

If you have already pressed it, and you wish

to cancel the delay time, proceed as follows:

• set the washing machine to PAUSE by

pressing button

• press the button

10 once. On the display will

appear the symbol «0’».

• press button

8 again to start the programme.

IMPORTANT!

• If the programme has already started, the

selected delay can be modified only after you

have turned the programme selector dial to

the «O» position and after you have selected

the programme again.

• The door will be locked throughout the delay

time. If you need to open the door, you must

first set the washer dryer to PAUSE by

pressing button

8. After you have closed the

door, press the same button again.

Note!

The Delay Start cannot be selected with

«Drain» programme.

132966720_GB.qxd 29/05/2009 11.34 Page 16

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nordland WD 8126 EL Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nordland WD 8126 EL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info