Bedienungsanleitung Nordmende DW60 (Seite 6 von 14) (Englisch)

493114

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

Makeyourmachine'swater hardness

settingacoordingto the resu~obtained

•throughthe testing strip.

LeooI,1, C' 1:' 'C'C'Cr:I-::I.:t. 1:-D" NoIJmo

Uwl2· ••• ~• , •• , _. _ ••••__

lA¥II3 I I I •• I • __ I Le.""~

••••••••. oJ I I I 1 I MedUI""'~

t__ IlewIIt6 -. I • I lintcorlllnl

LeooI.! • - - - - -. HiII>--

Wait for

1 min.

•• t«Jry

WasWOfy !limp •• on.

End lamp •• oM

n.~_~"on

W•• hOryawnp.ofI

End'-""illon..

The.urt'P ••.•••~

IS on

Waah'Dry Iiamp" off

End lamp. off

The

...w....••Qmp ieon

w..wrxy '-np illon.

&M:I~.on.

lhe~_'-'np.off

.""''''

EndlllmpirlO«

s-w__ lamp r. of\'.

End 18mp" on.

The smrw.,.. tampIiwnp ill oft

32-50 I

506-90 I 40-63

If the hardness of the water you use is above 90 dF (French hardness) or if you are using well

water; you are recommended to use filter and water refinement devices.

NOTE: Hardness level is adjusted to level 3 as a factory setting.

Adjusting salt consumption

Table of Water Hardness Level Settings

In order to understand whether or not the amount of softener salt in your machine is sufficient, check

the transparent section on the salt compartment cap. There is sufficient salt if the transparent section

is green. Salt has to be added if the transparent section is not green. ;

Testing strip .

The washing effectiveness of your machine depends on the softness of the tap water. For this reason.~

your machine is equipped with

a systenithat reduces the hardness in mains water supply. The - ~

washing effectiveness will increase when the system is correctly set. To find out the water hardness _

level of water in your area, contact your local water board or determine water hardness 19IIei by using ;:

the test strip(if available). \,

Open the Run Keepthe Shakethe

testing water testing testingstrip

strip. through strip in after takingit

your tap water for 1 out of water.

for 1 sec.

min.

'.",

~h"""",

ho_

.....

dHdF

•..

...•..

6-11

10-20

7-, .•

12·17

21-30

15--21

'a-21

31-4021-"

23-31

41-55

29·..,

PREPARING THE MACHINE FOR USE

The Importance of water decalcfflcatlon

For a good washing function, the dishwasher needs soft, I.e. less calcareous water. Otherwise, white

lime residues will remain on the dishes and the interior equipment. This will negatively affect your

machine's washing, drying and shining performance. When water flo~ through the softener system,

the ions forming the hardness are removed from the water and the water reaches the softness

required to obtain the best washing result. Depending on the level of hardness of the inflowing water,

these ions that harden the water accumulate rapidly inside the softener system. Therefore, the

softener system has to be refreshed so that it operates with the same performance also during the

next wash. For this purpose, dishwasher salt is used .

Filling with salt

Use softener salt specifically produced for use in dishwashers. To put softener salt, first remove

the lower basket and then open

the salt compartment cClJ? by

turning it counter clockwise.IJ ~ At

first fill the come,artment with 2kg

salt and water!] at overflowing,level If available,using the funne~

provided will make filling easier.;

refit the cap and close it. After

every 20th-30th wash, add salt

into your machine until it fills up

(approx.

1.5 kg)

Fill the salt compartment wtth

water at first use only.

We recommend that you use

small-grained or powder softener

salt.

Do not put table salt into your

machine. Otherwise, the function

of the softener compartment may

decrease over time. When you

start your dishwasher, the salt compartment gets filled with water.

Therefore, put the softener salt prior to starting your machine.

This way, overflowing salt gets immediately cleaned up through the wash operation. If you are not

going to wash any dishes immediately after putting salt, then run a short washing program with an

empty machine in order to avoid any damage ( to prevent corrosion) to your machine due to the salt

overflow while filling in the salt container.

Prior to using the machine for the first time

• Check whether the electricity and supply water specifications match the values indicated by the

installation instructions for the machine.

• Remove all packaging materials inside the machine.

• Set the water softener.

• Add 2 kg salt into the salt compartment and fill with water up to a level at which it will almost

overflow.

• Fill the rinse aid compartment.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nordmende DW60 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info