Bedienungsanleitung Novoferm iso 20-2 (Seite 11 von 90) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

709189

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

The instructions for installation, operating and maintenance must be kept in a safe place as long as the door is in use!

- 3 -

Elevation adjustment of upper caster

( 19b ) With manually operated doors and NovoPort-

operator: centre of roller should slide into the tail end

R/L

approx. 5mm (starting point: lower edge of

upper roller holder 90

R/L

retainer must be flush with

the upper castor roller block) [

1.50ca

( 19c ) With door operator on ceiling: Roller should lie in

the upper corner of the tail end. [

1.50cb

( 20 ) Lift the door leaf and push into its final position. Secure

the door leaf so that it cannot fall down. Pull the two

single cable ends 12 from the mounting-aid bracket 18

(Warning: the cable can be under slight initial tension),

hook them into the lower cable rocker on the lower cable

mount 57

R/L

and clamp with security plug 22 [

1.55a,b

]. Do

not twist the double steel cables!!

( 21 ) Check spring tension: Before closing, the door must be

under a slight spring tension, so that the double steel

cables 12 do not jump out of the cable rollers 17

L/R

( 22 ) Closing the door.

( 23 ) When tensioning/detensioning the springs 11, suitable

protection is to be worn and the door leaf must be

secured so that it cannot fall down! To tighten the

springs 11, remove the spring connector 15 pull the spring

tightening strap to the back and allow it to catch safely (e.g.

using a fork spanner or open spanner form size 13) in the

next hole. Insert the spring connector 15 once more. The

hook-up of the left and right spring 11 may differ by one

hole. Carry out a test run (cf. Point 30) and repeat the

procedure, if necessary [

1.55c

( 24 ) Check the spring tension once more. Open the door

halfway. The door must remain open of its own accord in

this position.

( 24a ) If the door closes noticeably, increase the

extension spring tension in accordance with Point

26.

( 24b ) If the door opens noticeably, decrease the

extension spring tension in accordance with Point

26.

( 25 ) For manually-operated doors: mount staple plate 93 as

follows: [

1.60

]

( 25a ) Close door from inside and fix with screw clamps.

Hold staple plate 93

or 93

to the left or right of the

catch 79 and fasten to the respective punch outs

(rear series of holes) in the angle frame 1

with

+ S12 (S13, if necessary)[

1.60a,b

( 25b ) Open and close garage door several times to

check locking function. When closing, the catch 79

must snap into the staple plate 93

or 93

. If

necessary, slide staple plate 93

or 93

vertically to

adjust. Connect security angle 94 with staple plate

and 93

by screwing them with S6 and S12

[

1.60c

( 25c ) For manually operated doors: Fasten rope retainer

91 for hand rope 96 with S10 to the lowest section

[

1.60d

]. Lead rope 96 through the respective holes in

the rope retainer 91 secure with knot as well as hang

to connecting plate 18 [

1.60e

( 25d ) Mannually open door and mark the endposition of

top casters 90

/90

. Close the door and insert track

clip 89 + S14

at marked position and tighten. Space

between rearmost point to lowest point of clip has to

be equal [

1.60f,g

For door operator do not use hand rope!

Inspection instructions

( 26 ) For the sectional door to function properly and smoothly as

well as to ensure the maximum serviceable life, it is

essential that all parts are properly installed. In the event

that the door does not function perfectly, check the

following items:

( 27 ) Are the side angle frames, the frame panels and the

horizontal track pairs horizontally, vertically and diagonally

exactly aligned and securely fastened? [

1.35 f

]

( 28 ) Have all screws been securely tightened?

( 29 ) Are the track joints between the angle frames and the 89°-

bends smooth and well-aligned? (point 16)

( 30 ) Check spring tension: open door half-way. The door must

rest in this position without additional support.

( 31 ) Should the door sink or close, increase the tension of the

torsion springs. (point 24)

( 32 ) Should the door open further, reduce the tension of the

torsion springs. (point 24)

( 33 ) Have the spring connectors at the back corner connection

brackets been inserted?

( 34 ) Rollers: can all the rollers be turned effortlessly by hand

when the door is closed (cf. Point 19)?

( 35 ) Have the top rollers been adjusted correctly? (cf. Point

19b,c)?

( 36 ) Are the distances between the roller axles and roller

holders identical when the door is half opened?

( 37 ) Do the double steel cables lie in their guides exactly and

without twisting?

( 38 ) In the case of a door operator: has the locking system

been dismounted?

Dismounting instructions for sectional doors

Type iso9-2 / iso20-2 with extension spring,

disassembled version

- Dismounting should only be carried out by suitably qualified

fitters -

Please read carefully before dismounting

The following tools are necessary for dismounting work:

Fork or socket wrenches sizes 7, 10 and 13, reversible ratchet

handle with extension and wrench socket sizes 7, 10 and

13, cross-tip screwdrivers size 2 and 3, at least two screw

clamps, possibly a hammer and chisel.

Unhooking the springs

Warning: Suitable protection is to be worn when

unhooking the springs and the door leaf must be

secured so that it cannot fall down!

Move the door leaf into the open position and secure it

against falling down. Remove the spring connectors.

Unhook the spring tightening straps from the spring hooks

and allow the spring tightening strap to catch securely in

the last hole. Insert the spring connectors.

Unhook the cable clamp of the double steel cable carefully

(double steel cable might be under slight initial tension)

from the lower cable rocker on the lower left and right mounts.

Close the door carefully.

Secure the pairs of horizontal tracks so they cannot fall down.

Dismount the 89° bends.

Unscrew the fixtures for the horizontal pairs of tracks from the

walls and ceiling.

Novoferm iso 20-2 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Novoferm iso 20-2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info