Bedienungsanleitung Novoferm iso 9-3 (Seite 10 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

709192

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

The instructions for installation, operating and maintenance must be kept in a safe place as long as the door is in use!

- 1 -

Installation instructions for sectional doors type

iso9-2 / iso20-2 with extension spring,

disassembled version

The door manufacturer accepts no liability for incorrect

mounting.

- Mounting should only be carried out by qualified fitters

Please read carefully before mounting

Scope of delivery:

Section package, frame package, panel package

The following items are required for mounting

• the following tools (place inside the garage before

mounting the door if there is no other entrance to the

garage)

folding rule/tape measure, water level, water pump pliers,

reversible ratchet handle with extension and wrench socket

inserts size 7, 10 and 13 ( fork or wrench socket also

possible) fork or open spanner from size 13 for tightening

springs (cf. Item 29), cross-tip screwdrivers size 2 and 3,

slot screwdriver, hammer drill with drill bits, ∅10mm

(drilling depth of at least 65mm), at least 2 screw clamps,

possibly square timber, hammer, metalsaw, small nippers,

chisel and

•

••

•

Mounting material suitable for the building situation. Note:

Check that the wood screws S8 supplied and the plugs

S9 are suitable for the building situation before use.

•

••

•

Important :

•

••

•

The door may only be mounted in a finished opening

and on a finished floor!

• As a precautionary measure, compare the garage

dimensions with the coordinating size of the door before

mounting.

− minimum inside width of garage

= coordinating size –width + 180mm

− minimum garage ceiling height

=coordinating size –height + 120mm (also suffices for

door operators)

− minimum side room right and left = 55mm

• Letter/numeral combinations, e. g. S8

, refer to the

respective mounting and installation materials in the

illustrated section, a successive subscript L or R, e.

g. 1

, indicates a part for the left or right side (observe

markings on parts). The omission of a subscript L or R

indicates a part that can be used either left or right.

Figures in brackets, e. g. [

1.10

], refer to the respective

illustration in the illustrated section.

Mounting of door frame

( 1 ) Lay the angular frames 1

+ 1

on to wood or something

similar (to protect them from scratches) and screw together

the angular frame 1

+ frame panel 3 + angular frame 1

(tapping screws have already been pre-mounted) [

1.10a

( 2 ) Screw the leading plate 4 with S13

on top on the angular

frames 1

+ 1

[

1.10b

( 3 ) Loosely screw the wall anchor 7 to the angular frames

R/L

right and left with S6 + M12 according to the side

room.

( 3a ) Side room 55 - 120mm: Set the wall anchor 7 to the

inside

[

1.10ca

]

( 3b ) Side room more than 120mm: set the wall anchor 7

to the side

[

1.10cb

]

If other mounting materials are used, make sure they

have at least the same load-carrying capacity as the

supplied wall anchor 7.

( 4 ) Set up the door frame behind the opening, secure it so it

cannot fall over, and use the water level to align exactly

parallel and at a right-angle [

1.15

] (also ensure that the

frame panel 3 is level). Centre and clip panel retainers 13

to the upper frame part [

1.15d

]. Finally fasten with S8 + S9

[

1.15a,c,d,e

]. Put the srew S8 in the plastic bush 81 and fix

the foot of the frame

[

1.15b

]

. Note: do not twist or bend the

angular frames 1

R/L

; it might be necessary to fill the

space between frame and masonry with suitable

material before tightening the screws!!!

( 5 ) Screw each of the right 14

and left 14

pair of horizontal

tracks to end piece 16

R/L

[

1.20a

] + upper rope fixation 5

[

1.20a

] + spring channel bracket 8 each front & back

[

1.20b,c

]+ end connection bracket 10

R/L

[

1.20d

] with S6 +

S12.

( 6 ) Stick on foamed rubber 9 on spring channel bracket 8

[

1.20b

], mount spring channel 12 with S6 + S12 and put on

the edge protection 24 on the front [

1.20e,f

( 7 ) Mounting of anchor tracks

( 7a ) If the distance between the wall and the pair of

horizontal tracks 14

R/L

is smaller than 500mm

(internal width of the garage max. coordinating size+

1030mm if door is fitted in the middle) push an

anchor track 27 with connecting brackets 28 right

and left into the track connector 6 and screw the

clamping plate 29 to S6

+ S12 in such a way that the

anchor tracks can still be pulled out

[

1.20a,b

]

( 7b ) If the distance between the wall and the pair of

horizontal tracks is more than 500mm the track

connector 6 can be later fixed to the ceiling (Cf .

Point. 14).

( 8 ) Screw the horizontal pair of tracks 14

R/L

to the end pieces

R/L

with the header bracket S5 + S12 so that later the

door remains raised when lifted up [

1.25c

]. If the distance to

the wall to small than use the hammer head screw S7

[

1.25c

]

( 9 ) Screw the track connector 6 each with S6 + S12 to the end

connection brackets 10

R/L

[

1.25d

( 10 ) Premount springs [

1.30

Place both triple extension spring assemblies 11 with the

plastic sliding elements downwards on the floor of the

garage (with the spring tightening strap pointing to the back

wall of the garage). Screw a deflection pulley cable

assembly 12 with the black side showing upwards to one

of the triple extension spring assemblies 11 with S5

+ S12.

This is the right spring assembly. Both cable ends are

Novoferm iso 9-3 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Novoferm iso 9-3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info