474197

Novoferm Novomatic 403 Seite 13

13
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
Programming the operator
Control elements
The controls for programming the door operator are
protected by a transparent cover. The transparent
cover can be opened with a screwdriver.
After the operator has been programmed, the
transparent cover must be closed again.
A.Numerical display shows the menu stage as well
as the selected value.
a. Point display, lights up to indicate “ready for
operation” and flashes on the hand transmitter code
learning completion.
a. Punktanzeige, leuchtet bei Betriebsbereitschaft
und blinkt bei Quittierung von eingelernten
Handsendercodes.
B.Button during the setting / adjustment phase
serves as an “up” button and outside the menu as
a start button.
C.Button during the setting /adjustment phase
serves as a “down” button.
D.Button is used to call up the setting/adjustment
menu, to change the menu stages and to store the
Settings.
The programming of the control unit is menu-driven.
By pressing button , the menu guide is called up.
The numbers displayed indicate the menu stage.
After approx. 2 seconds, the display flashes and the
setting can be altered via buttons and . The
selected setting is stored with button . And the
programme jumps automatically to the next menu
stage. By repeatedly pressing button , menu
stages can be skipped. To quit the menu, press
button until “0” is shown again. Outside the menu,
button can be used to generate a start impulse..
Before programming
- Allow door to engage into the carriage.
- Pull out the mains plug. Point display (a) lights up.
- Make sure that the aerial is correctly positioned
(see figure 13).
- Observe the hand transmitter instructions.
Menu stage 1: Programming the start
function for the hand transmitter
Briefly press button .
“1” is displayed.
Sas soon as the display flashes, press and keep
pressed for approx. 1 second the button of the hand
transmitter, with which you later wish to start the
operator.
As soon as the code has been read, the red point
display (a) flashes five times before quitting.
Further hand transmitters (up to a maximum of 10)
can be programmed.
Menu stage 2: Programming the light
function for the hand transmitter
Press button .
“2” appears in the display.
Note: If no 4-minute light is to be programmed,
repress button . The display shows “0” -
programming is completed.
Press the second button on the hand transmitter,
witch which the 4-minute light is to be switched on.
As soon as the code has been read, the red point
display (a) flashes five times before quitting.
After the code has been learned, briefly press
button .
“0” appears indicating that you have come to the end
of the menu.
Deleating all the hand transmitters programmed
for the operator:
Plug in the operator ‘s main plug while pressing
button .
. Menu stage 3: Setting/adjusting the top
14
15
16
17
19
end-of-travel position
Keep button pressed for 5 seconds. Number 3
appears in the display 14 a..
Wait a short while until the 3 starts flashing.
Press button and make sure that the door travels in
the OPEN direction.
If the door travels in the wrong direction CLOSE,
keep button pressed for another 3 seconds.
!
“3” flashes briefly. The travelling direction is
Altered.
Now travel by pressing button into the desired door
end position OPEN 17b.
By pressing button , the position can be corrected
into direction CLOSE.
Once the desired OPEN end-of-travel position has
been reached, press button . The operator stores
the OPEN end-of-travel position and “4” appears in
the display.
Menu stage 4: Setting/adjusting the bottom
end-of-travel position
Wait a short while until “4” starts flashing.
Press button . The operator causes the door to
travel in the CLOSE direction as long as the button is
pressed. The position can be altered to the OPEN
direction via button ..
Once the desired CLOSE end-of-travel position has
been reached, press button . The operator stores
the CLOSE end-of-travel position and “5” appears in
the display.
Press button twice until “0” appears..
Force-learning cycle
We recommend setting the suitable door type in
!
menu stage 8 prior to the force-learning cycle.
During this opening and closing cycle, the
operator learns the force required to open and close
the door. A forcel imit does not apply! The cycles
must not be interrupted. During these cycles must
not be interrupted. During these cycles “0” appears
in the display.
- Press button . The operator causes the door to
open until the top end-of-travel position has been
reached.
- Now press button again. The operator causes
the door to close until the bottom end-of-travel
position has been reached.
- After approx. 2 seconds, “0”disappears.
Menu stage 5: The opening force limit
If you have previously quit the setting menu, press
button for 3 seconds until “3” appears. Then press
button twice until “5” appears..
After approx. 2 seconds, the display flashes showing
the set value of the opening force limit. The force limit
setting can be increased for decreased via buttons
and .
After setting the value, press button .
The display shows “6”.
Menu stage 6: The closing force limit
After approx. 2 seconds, the display starts flashing,
and the set value for the closing force limit is
displayed.
The force limit setting can be increased or decreased
via buttons and .
After setting the value, press button . “0” appears
in the display.
Finally, check the force settings, and, if necessary,
repeat the setting procedure.
The maximum force at the main closing edge must
not exceed 150 N!
Caution! If the force setting is too high, persons may
be placed at risk of injury.
The factory setting is 4!
18
18a
19
20
Checking the force limit facility
- Place an obstruction (e. g. operator’s cardboard
box) underneath the doors’s closing edge.
- Starting from the OPEN end-of-travel position,
actuate the door to close.
- The door travels towards the obstruction, stops and
travels back to the top end-of-travel position.
- The point display (a) must switch off for approx. 1
second. Then the operator functions as normal
again.
If the door springs have been changed or altered,
then the force learning cycle must be repeated:
proceed to menu stage 5 and keep button pressed
for 3 seconds. “0” appears in the display. Then
complete the force learning cycle as explained under
point 18a.
Special settings
Menu stage 7: Light phases
Press button for 3 seconds.
“3” appears in the display. .
Press button several times until menu stage 6 is
shown.
Keep button pressed again for 3 seconds until
“7” appears in the display.
Menu Light phase Warning 24V
Value phase
0 60 s - 60 s
1 90 s - 90 s
2 120 s - 120 s
3 240 s - 240 s
4 0 s 3 s 0 s
5 0 s 3 s 0 s
6 90 s 3 s 0 s
7 90 s 3 s TAM
8 0 s 10 s TAM
9 0 s 10 s TAM
If the warning phase is set, the light flashes before
the door starts to move and during the actual travel
cycle. The factory setting is 1.
TAM: OPEN signal, when the door is not closed 24V
are available for signalling.
Menüstage 8: Door fitting
Press button . “8” appears in the display.
The corresponding door type has to be chosen for an
ideal performance and for the optimisation of force.
Menu- Start Stop Start Stop
value open open closed closed
0 0 0 0 0
1 15 0 15 0
2 0 15 0 60
3 15 15 15 35
4 25 45 25 45
5 15 15 15 60
6 15 15 15 15
7 35 35 35 50
8 60 15 15 85
9 only smooth operation
These details correspond to the smooth operation
distance of the slide, measured in cm."
Important advice:
The factory-made adjustment of the value 4 should
be kept.
A modification of the soft operation distance is not
permissable unless official approval of the gate
manufacturer has been obtained.
Press button.
Subsequently press button . “0” appears in the
display.
21
Retain these installation, operating and maintenance instructions for the full duration of the operator’s service life!
GB
… 13 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

novoferm-novomatic-403

Suche zurücksetzen

  • Wie bekomme ich den Deckel vom Antrieb entfernt um die Glühbirne zu tauschen? Eingereicht am 23-10-2024 18:26

    Antworten Frage melden

  • Novoferm innentaster 107 Novoferm Novomatic 403 past das Eingereicht am 2-2-2022 14:31

    Antworten Frage melden

  • die programmierung scheint total quer zu laufen !! was nun? Eingereicht am 27-6-2018 12:23

    Antworten Frage melden

  • Tor schliest aber öffne sich selbständignach einer unbestimmten Zeit, morgends,mittags,nachts Eingereicht am 8-4-2017 17:46

    Antworten Frage melden

  • Sehr geehrte Damen und Herren,
    unser Tor öffnet sich nicht ganz und beim Schließen schließt es nicht ganz. Es scheint, als ob es stehen bleibt, wenn es zu schwer geht. Das Sektionaltor selbst hemmt oder hakt aber nicht, ist leichtgängig. Eingereicht am 5-4-2017 11:34

    Antworten Frage melden

  • Novoferm, novomatic 403
    zeigt Nr. "4" im Antriebsmotor und reagiert nicht mehr auf die Handsender, trotz neuer Batterien Eingereicht am 16-3-2017 13:12

    Antworten Frage melden

  • Zieht kurz an und bleibt dann stehen Eingereicht am 9-12-2016 19:24

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Novoferm Novomatic 403 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Novoferm Novomatic 403

Novoferm Novomatic 403 Bedienungsanleitung - Englisch, Holländisch, Französisch, Spanisch - 31 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info