Bedienungsanleitung Novoferm Novomatic 423 Accu (Seite 18 von 48) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

709102

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Retain these installation, operating and maintenance instructions for the full duration of the operator’s service life!

Fasteningthetracktooperatorhead

Fitting the connector attachment

Attaching the wall bracket

Slot track (as illustrated) with chain sprocket (2) onto

the operator shaft (1a) and screw down with the 4

self-tapping screws.

The enclosed door connector attachment is

suitable for all Novoferm up-and-over doors and

Novoferm ISO20 sectional doors.

Position door connector attachment (11) centrally on

the top edge of the door leaf.

Mark fixing holes and drill using 4 mm metal drill

(max. Drilling depth 10 mm) or use the existing drill

holes. Screw on attachment using enclosed self-

tapping screws 6.3 x 16 (4 - 6 screws up-and-over

door, 6 screws - ISO20).

For other sectional doors, use telescopic fitting

(17) (accessory).

In order to ensure that the door can run freely

underneath the track, distance “x” must be greater

than 20 mm. Choose distance “x” so that the angle of

the linking bar does not exceed 45° (see figure 11).

Mark the door’s highest point of travel “a” plus

distance “x” on the lintel.

Hold wall fastening (10) at the total height (”a” + “x”)

vertically over the door connector attachment drill,

drill holes for wall plugs and screw the wall bracket

onto the wall.

Place linking bar (12) between carriage (4) and the

door connector attachment (11) and connect at both

ends with the bolts. Provide bolts with security clips.

Attach security clips to bolts.

Suspendingtheboomfromtheceiling

Support straps

Note:

Connectingthedoorconnectorattachment

tothecarriage

Disengaging the carriage

Note:

Attach central support (13) to track (8) in front of the

connector (7).

Positioning the prefitted operator at an angle to the

door, screw to wall bracket (10). Lift up operator,

making sure that it cannot fall down, and align in such

a way that the track runs horizontal and parallel

between the door tracks.

Establish the length of the support straps for the

operator head and the central support. If necessary,

shorten using a saw,and then screw in place.

Before starting any drilling, cover over track

and operator head to protect them from drilling dust.

Mark fixing points on the ceiling, drill 10 mm holes for

plugs and screw on support straps.

If the toothed belt or chain appear to be too slack,

slight retensioning may be required. It may be

necessary to take up the slack by adjusting the

support straps.

In order to carry out further work, it may be necessary

to disconnect the operator from the door by pulling

the pull cord on carriage (4) and move the door

manually.

If the door is to be operated manually for a

longer period of time, then the locking pin must be

removed from parking position (a) on the left and with

theopull cord in locking position (b).

In order to relock, return the locking pin into the

• InstallationInstructions

Please read these instructions carefully prior to

installation!

Preparing for installation

The following tools are required

Attention:

Supplypackage=completeset

Overview

Track

Installation should only be carried out by persons

qualified to do so!

Incorrect installation can put the safety of persons at

risk!

In case of improper installation, the manufacturer’s

guarantee becomes void.

1. Check the stability of the door. Retighten the

screws and nuts on the door.

2. Check if the door is running smoothly. Lubricate

shafts and bearings. Check the petension of the

springs and if necessary re-adjust.

3. Establish the door’s highest point of travel (see

figure 6).

4. Close the door and disable any existing locks

out of operation, if necessary dismantle.

Parts of latching devices, which could

form pinch or shear points, have to be

dismantled.

5. For garages without a second entrance, an

emergency release is required (accessory).

6. If a wicket pass door is included, fit the wicket

door contact.

7. Insert the light bulb into the operator and fasten

the lamp cover with 2 screws 4.2 x 50.

- Drilling machine with

10 mm masonry drill

4 mm metal drill

- Metal saw

- Spanner,sizes 10, 13 mm

- Slotted screwdriver, width 3 mm

- Phillips screwdriver, size 2 x 100

- Spirit level

Check the supplied screws and wall

plugs prior to use to ensure that these are suitable for

the strctural conditions on site.

Items 2 - 9 are pre-assembled

1. Operator head

2. Driving pinion

3. Track, operator side

4. Carriage

5. Toothed belt or chain

6. Deflection roller

7. Connector

8. Track, door side

9. Tensioner

10. Wall bracket

11. Door connector attachment

12. Linking bar

13. Central support

14. Bag of screws

15. Hand transmitter

16. Support straps

17. Telescopic fitting for sectional doors

(accessory)

18. Accu-Pack with bracket

Remove the packaging and fold out the track to its

full lenght.

Push connector (7) centrally over the joint.

parking position (a) on the left and restore the

connection between the operator and the door. On

the next movement, the carriage automatically re-

engages.

connect

potential-free buttons and potential-free

relay outputs. Finally, replace the cover and

screw down.

Before using the operator for the first

time, it must be tested to make sure that it

is working properly and safely (see

section on Maintenance/Checks).

E. Connecting the aerial

F. Connection for external impulse generator

(accessory, e. g. key switch or digital coder) 13b

G.Input STOPA

Abreak at this input end causes the operator to

stop or prevents it from starting up.

Connection for wicket door contact 13c

(accessory)

H.Input STOP B

Connection for 2-wire photocell EXTRA626 13d

(accessory).

In case of increased need for personal safety, in

addition to the operator’s internal force limit, we

recommend installing a one-way photocell. Further

information on our range of accessories can be

found in our sales literature. Consult your specialist

dealer.

Aligning the aerial / Connecting plan

Note:

Impulse generators and external safety devices

It is essential to pull out the mains plug

before opening the cover!

Do not connect any live leads, only

When using an external aerial, the shielding

must be assigned to the adjacent terminal (F, on

right) 13b.

N.Connection for photovoltaic module.

Maximum permitted supply voltage 25V.

Mind correct polarity.

Place the sticker clearly visible on the inner surface

of the door.

Use o n l y m a n u f acturer ' s o riginal

batteries.

The distance from the Accu-Pack to the drive should

not exceed 160cm.

Attach the mounting bracket to the door

track. Remove the fastening screw at the

door track and fix the mounting bracket with

the screw.

Wall installation:

Use suitable fastening material.

Hang in the Accu-Pack.

Make sure that the Accu-Pack does not

obstruct traffic.

•

• Installation of theAccu-Pack

• Warning sticker

Install the mounting bracket

Novoferm Novomatic 423 Accu Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info