Bedienungsanleitung Novoferm Novomatic 823S B1200 (Seite 47 von 144) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

709108

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

Installation

B-1200

value

Description Remarks

0 Normal operation Factory settings

1 Normal operation

with ventilation

settings*

Allows the ventilation of the garage. In this mode, the garage door is

approximately 10 cm wide open. To start up the ventilation setting, press

the second button on the hand transmitter or use a DuoControl/Signal 111

(accessories) setting* that must be programmed in Menu 2.

The garage door can be closed at any time using the hand transmitter.

The garage door closes automatically after 60 minutes.

2 Partial opening of

side sectional door*

In this mode, the garage door is approximately 1 m wide open. To start up

the partial opening, press the second button on the hand transmitter or use a

button of DuoControl/Signal 111 (accessories)* that must be programmed in

Menu 2.

3 OPEN/CLOSE

buttons*

Impulse issue for OPEN command by pushing the rst button and for CLOSE

command by pushing the second button on the hand-held transmitter or the

button DuoControl/Signal 111 (accessories), which must be programmed in

menu 2.

4 Operation with

single-lane control**

Only possible in connection with the trafc light control A800 (accessories).

With the function Cancelling the green phase through the light barrier.

5 OPEN-CLOSE

operation with

single track

control**

Function like item 4, but without cancelling of the hold-open time. Function

process:

After pulsing in CLOSE position, the drive starts and the door moves into end

position OPEN. Another impulse entry during drive has no effect and the door

continues to open. After impulse entry in OPEN position, the door closes. On

impulse entry during closing, the door stops and starts again.

6 Automatic closing

(‘AR’)**

External safety facility. Impulse always causes an opening of the door.

After the hold-open time and warning time (setup menu A) the door closes

automatically.

An interruption of the photoelectric sensor during closing causes stop and

reverse direction. Interruption during opening drive has no effect.

7 Automatic closing

(‘AR’)**

Function as in point 6, however, an interruption of the photoelectric sensor

during open time causes early termination of open time and the warning time

starts.

8 Automatic closing

(‘AR’)**

Function as in point 7, however, an impulse during open time causes early

termination of open time and the warning time starts.

9 Automatic closing

(‘AR’)**

Same function as 8, but without early warning phase.

Remarks:

- *: The second button of the transmitter must be reset after changes in operating modes 1, 2 or 3.

- **: A photoelectric sensor must be installed.

3. Press the programming button (PROG button) (D).

In setting 0, 1, 2 and 5 value "0" is displayed. Menu end (poss. continue with force learning run).

In setting 6, 7, 8 and 9 value "A" is displayed. Continue with menu "A"

Warning:

Automatic door - Do not stop in the movement area of the door, because it may start

unexpectedly!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Novoferm Novomatic 823S B1200 Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info