Bedienungsanleitung Novy 1811 One Pro (Seite 67 von 74) (Deutsch, Englisch, Holländisch, Französisch)

741774

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

– 67 –

6.4 Increase and decrease the power level

The extraction tower can be set to 13 power levels, indicated

via the 4 LEDs with increasing intensity per level.

Activate a higher power level if strong odours or vapour are

present. The extraction tower then works at a higher ﬂow rate.

Adjusting the power level:

Increase the power

Brighter

LED(s)

Press

Decrease the power

LED(s)

dim

ess

‐

6.5 Low position of extractor

You can use the button to choose a ﬁxed power (250 m3/h),

while keeping the tower at a low level.

This function could be used for cooking an egg, for example.

Low position of extractor

Switch on

Press and hold

for 2 seconds.

Switch off

Press

Note: You can switch from low to high suction mode by pressing

the

button.

6.6 Auto-stop

In order to ensure the extraction does not keep running, the

motor switches off and the extraction tower closes automatically

after 3 hours (if the controller has not been changed during

these 3 hours).

6.7 Concentration of the ventilation

When cooking only on one side of the cooking plate, you can

concentrate the extraction of fumes on this side. Using the

switch you can concentrate the extraction of fumes on the left

or on the right side. This even further increases the efﬁciency

of the unit.

7 CLEANING INDICATIONS

7.1 Cleaning indication for grease ﬁlter



Indication: LED next tot lights

After 20 cooking hours, the LED next to the

symbol will

light up.



Follow the cleaning instructions as described in the

chapter, Cleaning.

After having cleaned and replaced the grease ﬁlters, reset the

cleaning indication.

Reset: press the

control key for 3 seconds.

7.2 Cleaning indication for recirculation ﬁlter

(only with recirculation)



Indication: LED next to

lights

After a ﬁxed time, the LED lights up next to the symbol

will light up. This indication indicates that the recirculation ﬁlter

needs to be regenerated.



Follow the cleaning instructions described in the

recirculation box / ﬁlter manual.

After the regeneration and after having replaced the recirculation

ﬁlter, reset the cleaning indication.

Reset: press the

control key for 3 seconds.

7.3 I/O module connection

(1801 One Power & 1811 One Pro from v13)

The device can be optional equipped with the Input/Output

module n° 990034.

When the input of the module is used in “closed” input situation

the extraction tower will move to the desired height only the

extraction will not start.

The leds next to the Cleaning indication

and will blink.

The extraction only starts when the input situation is “open”.

The input can be used for example in combination with a

sinwow switch in duct out mode.

When the output of the module is used the relay will close when

the extraction is active.

The output remains closed also 5 minutes after closing the

extraction tower.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Novy 1811 One Pro Seite 67

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Novy 1811 One Pro

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info