Bedienungsanleitung Novy 3775 (Seite 34 von 56) (Deutsch, Englisch, Holländisch)

741789

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Instructions for assembly

8 Instructions for assembly

8.1 Safety instructions for kitchen unit ﬁ tters

• Veneers, adhesives and plastic surfaces of

surrounding furniture must be temperature resistant

(at least 75°C). If the veneers and surfaces are not

suﬃ ciently heat resistant they may become deformed.

• Ensure that all live connections are safely insulated

when installing the hob.

• Cover strips between the wall and the worktop behind

the hob which are made of solid wood are permissible

as long as minimum clearances in accordance with

the installation diagrams are maintained.

• Minimum clearances of the hob cut-out towards the

rear are to be maintained in accordance with the

installation diagram.

• For installation directly next to a tall cupboard, a safety

distance of at least 50 mm must be ensured. The

side surface of the tall cupboard should be ﬁ tted with

heat resistant material. Due to working requirements,

however, the distance should be at least 300 mm.

• The packaging materials (plastic foil, polystyrene,

nails etc.) must be kept out of reach of children as

these parts are potentially dangerous. Small parts can

be swallowed and there is a danger of plastic sheeting

causing suﬀ ocation.

8.2 Ventilation

• The induction hob is ﬁ tted with a fan that switches

on and oﬀ automatically. The fan starts slowly when

the electronic system temperatures exceed a speciﬁ c

limit. When the induction hob is used intensively,

the fan will switch to a greater velocity. Once the

electronic system has cooled down suﬃ ciently,

the fan will reduce its velocity and switch oﬀ again

automatically.

• Clearance between the induction hob and kitchen

furniture or built-in units must provide for suﬃ cient

ventilation of the induction hob.

• If the power level of a cooking zone is automatically

raised or lowered (see section on thermal cut-oﬀ

device) it is likely that the cooling system does not

cool suﬃ ciently. In this case we recommend that

the back wall of the bottom kitchen unit in the area

of the worktop cut-out be opened and that the front

transverse strip of the unit be removed over the

entire width of the appliance in order to promote the

circulation of air.

min. 5 mm

min. 20 mm

min. 5 mm

min. 20 mm

min. 30 mm

In order to better ventilate the hob, an air gap of 5 mm

should be left at the front.

8.3 Installation

Important information

• Remove any transverse strips underneath the worktop

at least in the area of the worktop cut-out.

• The induction hob may not be used when pyrolysis

operation is taking place in a built-in oven.

• When installing the appliance on top of a drawer it

is essential to ensure that no sharp items are stored

in the drawer since these could become bent on the

underside of the hob and prevent the drawer from

being opened and closed.

• If a shelf has been inserted underneath the hob,

there must be a clearance of at least 20 mm to the

underside of the hob in order to ensure that the hob is

suﬃ ciently ventilated.

• The hob may not be installed above refrigerators,

freezers, dishwashers, washing machines or dryers.

• To avoid danger of ﬁ re, make sure that no combustible

objects which could easily catch ﬁ re or become

deformed on exposure to heat are directly next to or

under the surface.

Sealing of the hob

Before installation, correctly insert the sealing unit

delivered with the hob.

• No liquids may penetrate between the edge of the hob

and the worktop or between the hob and the wall and

come into contact with any electrical appliances.

• When installing a hob into an uneven worktop, e.g.

with a ceramic or similar covering (tiles etc.), the seal

on the hob is to be removed and the seal between the

hob and worktop made with plastic sealing materials

(putty).

• The hob must under no circumstances be sealed with

silicone sealant! This would make it impossible to

remove the hob at a later date without damaging it.

Worktop cut-out

Cut out the worktop recess accurately with a good,

straight saw blade or recessing machine. The cut edges

should then be sealed so that no moisture can penetrate.

The area is cut out as illustrated. The glass ceramic hob

must have a level and ﬂ ush bearing. Any distortion may

lead to fracture of the glass panel. Make sure that the

sealing of the hob is properly seated.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Novy 3775 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info