Bedienungsanleitung Novy 6811 (Seite 36 von 44) (Deutsch, Englisch, Holländisch, Französisch)

741651

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

– 36 –

To decrease the power level press key

− Three green LEDs

show positions one to three.

− The red LED

shows the Power position. The Power

position is only used if there are strong odours, or a lot

of smoke or vapour. Its use must be kept to a minimum

because of the large extraction of air in this position.

− The Power position automatically goes back to speed

three after 6 minutes.

−

The motor has a thermal switch that switches the motor

off with overheating. After cooling the motor will switch

on again.



Determining the cause of overheating is re-

quired. This can be caused for example by a

pan ﬁ re, theimpeller motor being blocked or

an object getting in the exhaust opening and

causing it to bepartly or fully blocked.

Auto-Stop

To avoid the extractor hood from staying on, the motor is

automatically switched off after 3 hours (only if in 3 hours

operation has not been changed). The extractor hood

lighting stays on.

2.3 Lighting

Turning the lighting on and off

To turn the lighting on or off press

The light works independent of the motor.

The LED lighting has a soft on/soft off mode, which means

that the lighting will evenly go on and off. When switching

on the lighting, this will always light up with full power and

it can also be used when the fan is off.

Dimming LED lighting

When the LED lighting has been switched on, it can be

dimmed by keeping key

pressed.

Change in colour temperature with LED-lighting

You can change the colour temperature of the LED-lighting

from 2.700 K (warm white) into 4.000 K (neutral white). The

description for changing this can be found in section 3.4.

2.4 Programming recirculation (optional)



If recirculation is selected programming must

takeplace once.

This programming function activates the replacement

indicator of the monobloc recirculation ﬁ lter and the delay

time is changed.

Activating programming

− The motor must be switched off

−

Press the

and the

keys at the same time for 3

seconds until the red LED ﬂ ashes 5 times.

The following functions then operate:

−

Replacement indicator of the monobloc ﬁ lter is activated.

After a set time a red indicator light on theappliance

shows that the monobloc ﬁ lter must be replaced.

−

The delay time is set to 30 minutes (instead of the default

10 minutes).



Use the delay time of 30 minutes so the

cookingodours can be properly removed in

the monobloc ﬁ lter.

Read paragraph 3.3 for more information about replacement

of the monobloc recirculation ﬁ lter.

Deactivating programming

− The motor must be switched off

− Press

and

at the same time for 3 seconds until

the 3rd green LED ﬂ ashes 3 times.

The delay time is again set to 10 minutes (instead of 30 min-

utes) and cleaning indicator for recirculation is switched off.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Novy 6811 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Novy 6811

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info