Bedienungsanleitung Nuk Eco Control Audio 500 - 10256438 (Seite 11 von 15) (Englisch)

803241

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

6.4 Adjusting the volume

control

1. You can use the VOL + 10 and VOL - 11

buttons to set the volume at which you

hear the sounds emitted by the parent unit.

Each time you press one of the buttons you

will hear a beep at the volume that is

currently set up and it will show you with

the accordance of lit LEDs 16. The louder

your chosen setting, the louder any beeps

will be and the more LEDs will light up.

Note: When the VOX function is set to

low sensitivity (see "6.3 Using the VOX

function to adjust the transmission

sensitivity" on page 28), then quiet

sounds will not be transmitted regardless

of the volume setting. This means that

turning up the volume will not enable you

to hear anything more. If you want to hear

more of the sounds from the nursery you

will need to increase the transmission

sensitivity by selecting a higher VOX

level.

6.5 Mute setting

The parent unit can be “MUTED”. Sounds

from the nursery will then no longer be

transmitted.

1. Press the VOL - 11 button repeatedly

until you can no longer hear beeping.

No sounds will now be transmitted.

2. The LEDs 16 will continue to indicate the

noise level in the nursery. The more LEDs

are lit the louder are the noises in the

nursery.

3. You can cancel the mute setting by

pressing the VOL + 10 key.

4. If the parent unit is muted and you

activate the Talk-Back function, the

volume will automatically return to the

first level.

6.6 Talk-Back function

You can use the “Talk-Back” function to

speak to your baby.

1. Hold down the TALK 18 button on the

parent unit.

When you hear a beep, this means that

voice connection is established.

2. At the same time, speak into the

microphone 20 on the parent unit.

Your baby can now hear your voice from

the loudspeaker 2 on the baby unit.

3. Release the TALK 18 button in order to

hear the baby’s reaction.

Notes:

– If the baby unit 1 is in Eco-Mode, this

function is deactivated so that you do

not inadvertently wake your baby. In

this case, two consecutive beeps will

remind you that the Talk-Back function

is currently not available.

– If the volume of the parent unit is set to

“MUTE” (see "6.4 Adjusting the volume

control" on page 29), it will

automatically be increased to level 1 as

soon as you press the TALK 18 button.

7. Cleaning and care

7.1 Cleaning

Warning! To avoid the risk of electric

shocks, injuries and damage:

– Always disconnect the mains

adapter from the power socket

before cleaning the device.

– Never immerse the individual

parts in water.

Caution! Under no circumstances use

abrasive, corrosive or scratching cleaning

agents, as these could damage the device.

1. If necessary, wipe the individual parts

with a damp cloth.

2. Only use the baby monitor again when all

the parts have fully dried out.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nuk Eco Control Audio 500 - 10256438 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nuk Eco Control Audio 500 - 10256438

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info