Bedienungsanleitung Nuk Eco Control Audio 500 - 10256438 (Seite 7 von 15) (Englisch)

803241

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

2. Put the battery in its compartment as

indicated on the unit. Make sure you

insert it with the correct polarity (+ and -).

3. Slide the battery cover 9 back onto the

parent unit 8.

4. Insert the small plug of the mains adapter

into the mains adapter socket 19 of the

parent unit.

5. Insert the plug into a power socket that

matches the rating given in the technical

data (see "9. Technical data" on

page 31).

6. Initially, charge the parent unit

continuously for 10 hours to activate the

full battery capacity.

Subsequently the battery will take only

about 5 hours to charge. It can also be

charged while the unit is in operation.

The POWER 15 LED indicates that

charging is in progress. If it:

– flashes green: the battery is currently

being charged;

– lights up green: the battery is fully

charged;

– lights up red and beeps at one minute

intervals: low battery warning. Within

about 15 – 20 minutes the parent unit

will switch off automatically.

4.2 Connecting the baby unit

Note: Don’t install the baby unit 1 until the

battery of the parent unit 8 is fully charged.

1. Put the baby unit 1 somewhere in the

nursery where your baby will not be able

to reach it.

An optimal distance between baby and

the baby unit is from 1 to 2 m.

2. Insert the mains adapter plug into the

socket 3 of the baby unit 1.

3. Insert the plug into a power socket that

matches the rating given in the technical

data (see "9. Technical data" on

page 31).

4.3 Connecting baby unit and

parent unit

1. Use the On/Off button 5 to switch the

baby unit 1 on. Keep the button pressed

for a moment until the Power LED 6 lights

up.

2. Use the On/Off button 14 to switch the

parent unit 8 on. Keep the button pressed

for a moment until the LED 15 lights up a

steady green.

The connection will be set up

automatically. While this is being done

the connection indicator 13 will light up

red.

As soon as the connection has been

established, the connection indicator on

the parent unit 13 and the VOX LED on

the baby unit 7 will light up green.

If the connection indicator 13 begins to

flash green, this means that there is a

connection between the parent unit and

the baby unit, but your baby is currently

asleep and therefore the device has

automatically activated Eco-Mode to

reduce the high-frequency radiation in

the children’s room and save energy.

In the event that the connection between

the parent unit and the baby unit breaks

down, the devices will automatically attempt

to establish a new one.

If a new connection is not established within

30 seconds, the parent unit 8 will emit a

regular beep and the connection

indicator 13 will light up red. You may need

to move the parent unit to a different

location before a new connection can be

established.

3. First go and check on baby to make sure

everything is OK.

4. Then try to set up a new connection by

moving about.

The connection will be automatically re-

established as soon as you are within

range.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nuk Eco Control Audio 500 - 10256438 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nuk Eco Control Audio 500 - 10256438

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info