Bedienungsanleitung Nuk Eco Control Audio 500 - 10256438 (Seite 10 von 15) (Englisch)

803241

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

• The power supply indicator POWER 15:

– lights up green: the device is switched

on and the battery is fully charged;

– flashes green: the battery currently

being charged;

– lights up red and beeps at one minute

intervals: low battery warning. Within

about 15 – 20 minutes the parent unit

will switch off automatically. Please be

aware that this interval may be

reduced, depending on how you use

the device (for example, VOX level 5

uses more power than level 1).

• The display 16 with the 5 LEDs has three

functions. The LEDs are only visible when

in use.

– indicates the noise level in the nursery.

The more LEDs are lit, the louder the

noises;

– indicates the different levels when you

are adjusting the volume. The more

LEDs are lit, the louder the sound from

the loudspeaker;

– indicates the different levels when you

are adjusting the VOX sensitivity. The

more LEDs are flashing, the sooner the

device will react to sounds. If 5 LEDs

are lit the device will switch to

continuous transmission.

6.3 Using the VOX function to

adjust the transmission

sensitivity

Babies make a lot of different noises. These

can range from loud breathing through

babbling to calling or loud crying. The VOX

function can be set up in such a way that

only loud sounds such as crying or calling

are transmitted while quieter sounds are not

registered.

The VOX function sets up the transmission

sensitivity of the microphone. The higher the

VOX level the more sensitive the device is to

noises.

1. You activate the VOX function by briefly

pressing the VOX button 17.

The LEDs 16 indicate the sensitivity of

the current setting by flashing.

2. You can increase or decrease the

transmission sensitivity by pressing one

of the buttons VOL + 10 or VOL - 11. The

number of flashing LEDs 16 corresponds

to the selected level:

– VOX level 1 = extremely low sensitivity,

reacts only if baby screams really

loudly;

– VOX level 2 = low sensitivity, reacts if

baby screams loudly;

– VOX level 3 = normal sensitivity, reacts

if baby cries normally;

– VOX level 4 = high sensitivity, reacts

even to slight sounds;

– VOX level 5 = Eco-Mode is switched

off. The unit is set to transmit continu-

ously.

You can set up the volume at which the

parent unit should output the transmitted

sounds using the two buttons VOL + 10 and

VOL - 11 (see "6.4 Adjusting the volume

control" on page 29).

Note: After activating the VOX function, you

have about two seconds to alter the

transmission sensitivity. The device will then

automatically switch back to transmitting

sounds. You can see this has happened

because the LEDs 16 will no longer be

flashing, and the VOL + 10 and VOL - 11

buttons now only modify the volume.

Caution! In continuous transmission mode

at VOX level 5, all sounds are transmitted

continuously. When the baby is sleeping

peacefully, the volume is automatically

reduced to its lowest level after a few

seconds to minimise background noise. As

soon as the child begins to make a noise,

the volume automatically returns to its

previous setting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Nuk Eco Control Audio 500 - 10256438 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Nuk Eco Control Audio 500 - 10256438

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info