Bedienungsanleitung Numark 5000FX (Seite 4 von 48) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

23414

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

REAR CONNECTIONS

INPUTS

1. AC INPUT and Power Switch: This

mixer is designed to work with the

power supply cord that comes with the

unit. While the power switch on the

mixer is off, plug the power supply into

the mixer first, then plug it into the

outlet. Use this power switch to turn on

the mixer after all input devices are

already connected to prevent damage to

your equipment. Turn the mixer on

before you turn on amplifiers and turn

off amplifiers before you turn off the

mixer.

2. Microphone Inputs (DJ MIC) & (2):

Microphones with a 1/4” or XLR

connector can be connected to the DJ

MIC (XLR connection is on face panel).

MIC 2 accepts a standard 1/4”

connection.

3. Line Inputs: CD players, Tape Decks,

Samplers or other line-level input

devices should be connected to these

inputs.

4. Phono/Line Inputs: This input is used

for connecting your turntables through

the sensitive RIAA phono preamplifiers.

You can also connect line-level devices

here if the Phono/Line switch is set to

“line”.

5. GND (Ground Posts): Use this

connector to attach to turntables or

other devices that need to be grounded

to the mixer’s chassis.

6. Phono/Line (Source switch): This

switch activates and deactivates the

RIAA phono preamplifiers. Only

turntables with phono-level output

should be assigned when the switch is in

the phono position. Some turntables

offer line-level output. To use these

turntables and other line devices like CD

players, switch the input to Line.

OUTPUTS

7. Fader Start Outputs CFA, CFB: Use

standard 1/8” (3.5mm) cables to

connect these outputs to Numark and

other popular brands of CD players

equipped with remote start. CFA and

CFB represent the Fader start on

Crossfader “A” and “B” side

respectively.

8. Zone Output: The MASTER output can

be routed to the ZONE output. The

ZONE knob controls the level of this

output.

9. Booth Output: Connect this output to

the DJ booth speakers. The volume for

this output is independently controlled

on the face panel by the BOOTH knob.

10. Record Output: This output is for

connecting a recording device such as a

tape deck or CD recorder.

11. Digital Output: (RCA Digital) 44.1kHz

S/PDIF output. The format is type 2,

form 1, S/PDIF (Sony/Phillips Digital

Interface Format). This record level

output can be connected to compatible

devices such as CD Burners, Hard Drive

recorders, or other digital mixers.

Higher audio fidelity is maintained from

these outputs.

12. Master Output (RCA Analog): This

unbalanced output is for connecting to

an external monitoring device. The

level of this output is controlled by the

MASTER volume knob on the face panel,

but not the rear panel attenuator.

13. Stereo Balanced Master Outputs

(XLR): low-impedance XLR type

connectors controlled by the Master

volume knob and the rear panel

attenuator.

14. Master Gain Reduction

(Attenuator): This knob limits the

maximum output level of the MASTER

XLR output to prevent amplifier/speaker

damage. It ranges from 0.245V to 2.0V

output.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Numark 5000FX Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info